Lenovo ThinkPad X200 Hardware Maintenance Manual - Page 34

Enter the BIOS Setup Utility and change Serial ATA SATA setting to, Table 1. FRU tests - ultrabase

Get Lenovo ThinkPad X200 PDF manuals and user guides View all Lenovo ThinkPad X200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Table 1. FRU tests FRU System board Power LCD unit Audio Speaker PC Card slot ExpressCard slot Keyboard Hard disk drive Diskette drive Optical drive Memory TrackPoint or pointing device Applicable test 1. Diagnostics ➙ CPU/Coprocessor 2. Diagnostics ➙ Systemboard 3. If the ThinkPad X200 UltraBase™ is attached to the ThinkPad computer, detach it. Place the computer on a horizontal surface, and run Diagnostics ➙ ThinkPad Devices ➙ HDD Active Protection Test. Note: Do not apply any physical shock to the computer while the test is running. Diagnostics ➙ ThinkPad Devices ➙ AC Adapter ➙ Battery 1 (Battery2) 1. Diagnostics ➙ Video Adapter 2. Interactive Tests ➙ Video Enter the BIOS Setup Utility and change Serial ATA (SATA) setting to Compatibility, and run Diagnostics ➙ Other Device ➙ Conexant Audio Interactive Tests ➙ Internal Speaker Note: Once Modem/Audio test is done, the no sound is heard this test. In this case, turn off and turn on the computer. Then, run this test again. Diagnostics ➙ Systemboard ➙ PCMCIA 1. Insert a PCI-Express/USB Wrap card into the ExpressCard slot. 2. Turn on the computer. 3. Run Diagnostics ➙ ThinkPad Devices ➙ ExpressCard slot. 1. Diagnostics ➙ Systemboard ➙ Keyboard 2. Interactive Tests ➙ Keyboard Enter the BIOS Setup Utility and change Serial ATA (SATA) setting to Compatibility, and run Diagnostics ➙ Fixed Disks. You can also diagnose the hard disk drive without starting up the operating system. To diagnose the hard disk drive from the BIOS Setup Utility, do as follows: 1. Remove any diskette from the diskette drive, and then turn off the computer. 2. Turn on the computer. 3. While the message, "To interrupt normal startup, press the blue ThinkVangate button," is displayed at the lower left of the screen, press F1 to enter the BIOS Setup Utility. 4. Using cursor keys, select HDD diagnostic program. Press enter. 5. Using cursor keys, select Main hard disk drive or Ultrabay hard disk drive. 6. Press Enter to start the diagnostic program. 1. Diagnostics ➙ Diskette Drives 2. Interactive Tests ➙ Diskette 1. Diagnostics ➙ Other Devices ➙ Optical Drive 2. Interactive Tests ➙ Optical Drive Test 1. If two DIMMs are installed, remove one of them and run Diagnostics ➙ PM Memory. 2. If the problem does not recur, return the DIMM to its place, remove the other one, and run the test again. If the TrackPoint does not work, check the configuration as specified in the BIOS Setup Utility. If the TrackPoint is disabled, select Automatic to enable it. After you use the TrackPoint, the pointer may drift on the screen for a short time. This drift can occur when a slight, steady pressure is applied to the TrackPoint pointer. This symptom is not a hardware problem. If the pointer stops after a short time, no service action is necessary. If enabling the TrackPoint does not correct the problem, run Interactive Tests ➙ Mouse 28 Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
Table 1. FRU tests
FRU
Applicable test
System board
1.
Diagnostics
➙
CPU/Coprocessor
2.
Diagnostics
➙
Systemboard
3. If the ThinkPad X200 UltraBase
™
is attached to the ThinkPad computer, detach it.
Place the computer on a horizontal surface, and run
Diagnostics
➙
ThinkPad
Devices
➙
HDD Active Protection Test
.
Note:
Do not apply any physical shock to the computer while the test is running.
Power
Diagnostics
➙
ThinkPad Devices
➙
AC Adapter
➙
Battery 1 (Battery2)
LCD unit
1.
Diagnostics
➙
Video Adapter
2.
Interactive Tests
➙
Video
Audio
Enter the BIOS Setup Utility and change Serial ATA (SATA) setting to
Compatibility
,
and run
Diagnostics
➙
Other Device
➙
Conexant Audio
Speaker
Interactive Tests
➙
Internal Speaker
Note:
Once Modem/Audio test is done, the no sound is heard this test. In this case,
turn off and turn on the computer. Then, run this test again.
PC Card slot
Diagnostics
➙
Systemboard
➙
PCMCIA
ExpressCard slot
1. Insert a PCI-Express/USB Wrap card into the ExpressCard slot.
2. Turn on the computer.
3. Run
Diagnostics
➙
ThinkPad Devices
➙
ExpressCard slot
.
Keyboard
1.
Diagnostics
➙
Systemboard
➙
Keyboard
2.
Interactive Tests
➙
Keyboard
Enter the BIOS Setup Utility and change Serial ATA (SATA) setting to
Compatibility
,
and run
Diagnostics
➙
Fixed Disks
.
Hard disk drive
You can also diagnose the hard disk drive without starting up the operating system. To
diagnose the hard disk drive from the BIOS Setup Utility, do as follows:
1. Remove any diskette from the diskette drive, and then turn off the computer.
2. Turn on the computer.
3. While the message, “To interrupt normal startup, press the blue ThinkVangate
button,” is displayed at the lower left of the screen, press F1 to enter the BIOS
Setup Utility.
4. Using cursor keys, select
HDD diagnostic program
. Press enter.
5. Using cursor keys, select
Main hard disk drive
or
Ultrabay hard disk drive
.
6. Press Enter to start the diagnostic program.
Diskette drive
1.
Diagnostics
➙
Diskette Drives
2.
Interactive Tests
➙
Diskette
Optical drive
1.
Diagnostics
➙
Other Devices
➙
Optical Drive
2.
Interactive Tests
➙
Optical Drive Test
Memory
1. If two DIMMs are installed, remove one of them and run
Diagnostics
➙
PM
Memory
.
2. If the problem does not recur, return the DIMM to its place, remove the other one,
and run the test again.
TrackPoint or pointing
device
If the TrackPoint does not work, check the configuration as specified in the BIOS Setup
Utility. If the TrackPoint is disabled, select
Automatic
to enable it.
After you use the TrackPoint, the pointer may drift on the screen for a short time. This
drift can occur when a slight, steady pressure is applied to the TrackPoint pointer.
This symptom is not a hardware problem. If the pointer stops after a short time, no
service action is necessary.
If enabling the TrackPoint does not correct the problem, run
Interactive Tests
➙
Mouse
28
Hardware Maintenance Manual