LevelOne WAC-1001 User Manual - Page 9

Installation Guidelines, 3 Items Required for Installation, 4 Installing the Device

Get LevelOne WAC-1001 PDF manuals and user guides View all LevelOne WAC-1001 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

2.2 Installation Guidelines 1) Make sure that your workbench or standard rack is level and stable. 2) Do not place heavy objects on the Device. 3) Make sure that there is proper heat dissipation and adequate ventilation around the Device. 4) Position the Device out of direct sunlight and away from sources of heat and ignition. 5) Please use the supplied power cord. 2.3 Items Required for Installation 1) Broadband Internet connection 2) Tools and equipment： (1) Broadband modem (optional) (2) PC with an Ethernet card and TCP/IP installed (3) Network devices like hub, switch, wireless access point (4) Phillips screwdriver (5) Power outlet. 2.4 Installing the Device Before you install the Device, make sure your Internet connection is working properly. If it is not, please contact your ISP. 1) Installing the Device on a Flat Surface (1) Make sure the Device is powered off. (2) Place the Device upside down on a sturdy, flat bench with a power outlet nearby. Verify that the bench is well grounded. (3) Remove the adhesive backing from the supplied rubber feet. Attach the four rubber feet to the round recessed areas on the bottom of the Device. (4) Turn the Device over to make it right side up on the bench 2) Installing the Device in a 19-inch Standard Rack Follow these steps to install the Device in a 19-inch standard rack: (1) Make sure the Device is powered off. (2) Make sure the rack is stable and well grounded. (3) Attach the supplied rack-mount brackets to the left and right side of the Device with the supplied screws, and secure the brackets tightly, as shown in Figure 2- 2. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
5
2.2 Installation Guidelines
1) Make sure that your workbench or standard rack is level and stable.
2) Do not place heavy objects on the Device.
3) Make sure that there is proper heat dissipation and adequate ventilation around the Device.
4) Position the Device out of direct sunlight and away from sources of heat and ignition.
5) Please use the supplied power cord.
2.3 Items Required for Installation
1) Broadband Internet connection
2) Tools and equipment
：
(1) Broadband modem (optional)
(2) PC with an Ethernet card and TCP/IP installed
(3) Network devices like hub, switch, wireless access point
(4) Phillips screwdriver
(5)
Power outlet.
2.4 Installing the Device
Before you install the Device, make sure your Internet connection is working properly. If it is not, please contact
your ISP.
1) Installing the Device on a Flat Surface
(1) Make sure the Device is powered off.
(2) Place the Device upside down on a sturdy, flat bench with a power outlet nearby. Verify that the bench is
well grounded.
(3) Remove the adhesive backing from the supplied rubber feet. Attach the four rubber feet to the round
recessed areas on the bottom of the Device.
(4) Turn the Device over to make it right side up on the bench
2) Installing the Device in a 19-inch Standard Rack
Follow these steps to install the Device in a 19-inch standard rack:
(1) Make sure the Device is powered off.
(2) Make sure the rack is stable and well grounded.
(3) Attach the supplied rack-mount brackets to the left and right side of the Device with the supplied screws,
and secure the brackets tightly, as shown in
Figure
2- 2.