Lexmark 4033 User Guide - Page 2

IBM 4033/Lexmark MarkNet OSR Models 2XX, 3XX: The Status LED blinks to indicate an error was detected after a successful Reset. The Test and Data LEDs indicate what type of error was detected: Status Test Data Error Action blink off off software Contact next level of support. blink off on network Refer to Printer and LAN Checks. Note: If you are updating the flash code, the Status, Test, and Data LEDs will all blink. This does not indicate an error. Sample Print Test (Models 20X and 30X) Press and release the Test button to send a single-page file to all ports. If the test is successful, go to "LAN Connection Check." If the print test fails, go to "Wrap Test for Adapter Ports." Wrap Test for Adapter Ports To test any port: 1. Disconnect the printer cable from the adapter. 2. Install a wrap plug on that port. 3. Press Reset. Models 0XX: The Status LED will blink several times within 3 to 4 seconds, turn off for up to 10 seconds, then blink continuously in a pattern of two blinks, a pause, then two blinks. Any other pattern on blinks indicates a failure of the Replace the adapter if the test fails. Models 20X and 30X: Status off off off Test off blink blink Data blink off blink Failure Parallel 1 port wrap failure Parallel 2 port wrap failure Serial port wrap failure A successful test results in only the Power and Status LEDs on, just like a normal Reset. Replace the adapter if the test fails. LAN Connection Check 1. For Token-Ring using shielded twisted-pair cable (Models 001, 011, 201, or 301): Disconnect the LAN cable from the network, leaving it connected to the adapter. For Ethernet 10Base2 (Models 003, 013, 202, or 302): Make sure the switch is set to position 2 for Models 003 and 013, or position 16/2 for Models 202 and 302. Attach a 50 ohm BNC terminator cap to each end of the T-connect or. (The customer may be able to supply these caps.) For Token-Ring using unshielded twisted-pair cable (Models 201 or 301 ) or Ethernet 1 10BaseT (Models 002, 012, 202, or 302): There is no LAN connection test for these configurations. Refer to "Printer and LAN checks." 2. Press the Reset button. Models 0XX: The status LED will blink several times within 3-4 seconds, turn off for up to 30 seconds, then turn on solid. Models 20X and 30X: The adapter will go through a reset cycle and stop with on the Power and Status LEDs on. Any other result indicates a failure of the test. For Token-Ring using shielded twisted-pair cable, verify the continuity of the cable and replace the adapter if the cable is good. For Ethernet 1 10Base2 replace the adapter. Printer and LAN checks Reset Cycle Test Power Status Test Data 1 on off off off 2 on on on on 3 on off on on 4 on off on off 5 on off off on 6 on off off off End on on off off If the adapter checks out successfully, the problem may be with other hardware or software on the network. The following are suggestions to the customer for checking hardware and software for possible problems. Printer checks Make sure the printer is operating correctly by running printer diagnostics and the printer wrap test. Make sure the printer is configured for the right type of port (parallel or serial). Make sure the jumper and power cords are properly connected. Make sure the printer is queued and the printer driver is configured properly. Make sure the proper adapter port has been associated (parallel or serial). Make sure the adapter's printer port parameters match those of the printer (for example, parallel mode, serial baud rate, and serial protocol). LAN checks Make sure the software utility has been correctly installed. Make sure the LAN cable and LAN connections are good. Make sure a single route broadcast is supported across the network bridges, if a bridge is used. Make sure the server is working properly. Review print server installation and configuration using the appropriate system guide to operation. Parts Catalog 2XX, 3XX Models P/N 1381605 Description 4033- 201 Token-Ring network adapter 1381603 4033- 202 Ethernet network adapter 1381606 4033- 301 Token-Ring network adapter with serial port 1381604 4033- 302 Ethernet network adapter with serial port 1418613 Cover, switch 1418601 Cord set, jumper power 2182994 T-connector, Ethernet 9900769 Wrap plug, parallel 9900770 Wrap plug, serial 72X8546 Wrap plug, multifunction 0XX Models P/N 1333658 1333588 1333589 1333787 1333788 1333789 1333586 1333595 1333590 1333591 1333592 Description Adapter Asm., Model 4033-001 (no P/S) Adapter Asm., Model 4033-002 (no P/S) Adapter Asm., Model 4033-003 (no P/S) Adapter Asm., Model 4033-011 (no P/S) Adapter Asm., Model 4033-012 (no P/S) Adapter Asm., Model 4033-013 (no P/S) Operator Panel Board, 4033-001, 4033-011, Operator Panel Board, 4033-002, 4033-003, 4033-012, 4033-013 Power Supply, US Model 4033-001, 4033-002, 4033-011, 4033-012 Power Supply, US Model 4033-003, 4033-013, WT (except Nordic) Power Supply, Nordic 0XX Models (Continued) P/N 72X8546 Description Wrap Plug, multi-function 71F1168 Terminator Cap, 25 Ohm, BNC 1339517 Line Cord, US, Canada, Columbia, Saudi Arabia 6185888 Line Cord, US, 6 ft. 1339520 Line Cord, Europe 1339523 Line Cord, South Africa 1339522 Line Cord, Switzerland 1339524 Line Cord, Italy 1339525 Line Cord, Denmark 1339518 Line Cord, New Zealand/Australia, Argentina, Uruguay 1339521 Line Cord, Israel 1339519 Line Cord, UK 1339523 Line Cord, Pakistan 1339519 Line Cord, Hong Kong, Malaysia, Singapore, Burma, Brunei, India 1339523 Line Cord, Bangladesh, Sri Lanka 2 LM-4 IBM/TSS Internal Use Only