Lexmark MS811 PRESCRIBE Emulation Technical Reference Guide - Page 3

Introduction, Supported devices, Installing the PRESCRIBE emulation option, Flash memory and hard

Get Lexmark MS811 PDF manuals and user guides View all Lexmark MS811 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

Introduction 3 Introduction PRESCRIBE emulation option for Lexmark laser printers is an extended version of the firmware that includes a PRESCRIBE language processor. It enables the printer to be an effective replacement for Kyocera printers in select large accounts where the PRESCRIBE printer language is used. Since Kyocera does not offer a single standard version of PRESCRIBE across all of its products, the emulation compatibility of this version is based on testing with customer application test files and an extensive set of engineering commandlevel tests. This technical reference manual describes the capabilities of the PRESCRIBE emulation option and highlights the key limitations, which customers must consider in their certification testing. Supported devices • Lexmark MS812, MS811, MS810 • Lexmark MS610de, MS610dn • Lexmark MS510dn • Lexmark CS510de, CS510e • Lexmark CS410dn, CS410n Installing the PRESCRIBE emulation option Note: Installing the option may restore your printer to factory default settings. Before installing, print a Menu Settings page so that any non-default settings can be restored. For more information on installing and uninstalling the PRESCRIBE emulation option, see the installation instructions that came with the option, or the printer User's Guide. After installing the option, set up the PRESCRIBE FRPO (Firmware RePrOgram) defaults to match the Kyocera default setup on the applications. Many accounts use the Kyocera factory default settings and may not require further setup. For more information on the FRPO settings supported by the PRESCRIBE emulation option, see "FRPO: Firmware RePrOgram" on page 12. To verify installation, print a Print Menus page from the printer control panel. Under the Printer Information section, there should be an entry for the PRESCRIBE emulation option (example: "P-Scribe = P41G"). The second page that prints is a PRESCRIBE emulation STAT page with the current FRPO permanent settings. Flash memory and hard disk support PRESCRIBE downloaded fonts (LDFC) and PRESCRIBE macros can be stored on either the flash memory or the printer hard disk. Programming is done using the Resource Save setting. Note: The ICCD and WRED commands are not supported.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
Introduction
PRESCRIBE
emulation option for Lexmark laser printers is an extended version of the firmware that includes a PRESCRIBE
language processor. It enables the printer to be an effective replacement for Kyocera printers in select large accounts
where the PRESCRIBE printer language is used.
Since Kyocera does not offer a single standard version of PRESCRIBE across all of its products, the emulation compatibility
of this version is based on testing with customer application test files and an extensive set of engineering command-
level tests.
This technical reference manual describes the capabilities of the PRESCRIBE emulation option and highlights the key
limitations, which customers must consider in their certification testing.
Supported devices
•
Lexmark MS812, MS811, MS810
•
Lexmark MS610de, MS610dn
•
Lexmark MS510dn
•
Lexmark CS510de, CS510e
•
Lexmark CS410dn, CS410n
Installing the PRESCRIBE emulation option
Note:
Installing the option may restore your printer to factory default settings. Before installing, print a Menu
Settings page so that any non-default settings can be restored.
For more information on installing and uninstalling the PRESCRIBE emulation option, see the installation instructions
that came with the option, or the printer
User's Guide
.
After installing the option, set up the PRESCRIBE FRPO (Firmware RePrOgram) defaults to match the Kyocera default
setup on the applications. Many accounts use the Kyocera factory default settings and may not require further setup.
For more information on the FRPO settings supported by the PRESCRIBE emulation option, see “FRPO: Firmware
RePrOgram” on page 12.
To verify installation, print a Print Menus page from the printer control panel. Under the Printer Information section,
there should be an entry for the PRESCRIBE emulation option (example: “P-Scribe = P41G”). The second page that prints
is a PRESCRIBE emulation STAT page with the current FRPO permanent settings.
Flash memory and hard disk support
PRESCRIBE downloaded fonts (LDFC) and PRESCRIBE macros can be stored on either the flash memory or the printer
hard disk. Programming is done using the Resource Save setting.
Note:
The ICCD and WRED commands are not supported.
Introduction
3