Lexmark MX826 Paper and Specialty Media Guide PDF - Page 27

Troubleshooting, Rib pattern for Lexmark B2865, M5255, M5270, MB2770, MS725, MS821

Get Lexmark MX826 PDF manuals and user guides View all Lexmark MX826 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Guidelines for selecting and using paper 27 Rib pattern for Lexmark B2865, M5255, M5265, M5270, MB2770, MS725, MS821, MS822, MS823, MS824, MS825, MS826, MX721, MX722, MX725, MX822, MX824, MX826, XM5365, XM5370, XM7355, XM7365, XM7370 221.6 0.6 204.0 0.6 189.6 0.4 170.5 0.4 153.0 0.4 134.0 0.4 115.6 0.4 94.4 0.2 83.5 0.2 68.5 0.2 52.5 0.2 36.5 0.2 20.5 0.1 5.6 0.1 Reference Edge Troubleshooting The following table provides solutions to some common card stock and label problems. For more troubleshooting information, see your printer documentation. Problem Solution Print on heavy stock is blurred or out of focus. Make sure the Paper Type setting is correct for your print material. Note: Card stock in excess of 203 g/m2 (54‑lb bond) may not produce acceptable print results. Print on five sheets of paper, wait for approximately five seconds, and then print five more sheets of paper to remove any toner that may have accumulated. Toner rubs off the page. Make sure the Paper Type setting is correct for your print material. Use material that is lighter than 300 g/m2. Print on five sheets of paper, wait for approximately five seconds, and then print five more sheets of paper to remove any toner that may have accumulated. Printing shows voids. Change the Paper Type to Plain Paper. Print on five sheets of paper, wait for approximately five seconds, and then print five more sheets of paper to remove any toner that may have accumulated.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
Rib pattern for Lexmark B2865, M5255, M5265, M5270, MB2770, MS725, MS821, MS822,
MS823, MS824, MS825, MS826, MX721, MX722, MX725, MX822, MX824, MX826, XM5365,
XM5370, XM7355, XM7365, XM7370
Reference
Edge
221.6
204.0
189.6
170.5
153.0
134.0
115.6
94.4
83.5
68.5
52.5
36.5
20.5
5.6
0.6
0.6
0.4
0.4
0.4
0.4
0.4
0.2
0.2
0.2
0.2
0.2
0.1
0.1
Troubleshooting
The following table provides solutions to some common card stock and label problems. For more
troubleshooting information, see your printer documentation.
Problem
Solution
Print on heavy stock is
blurred or out of focus.
Make sure the Paper Type setting is correct for your print material.
Note:
Card stock in excess of 203 g/m
2
(54
‑
lb bond) may not produce acceptable
print results.
Print on five sheets of paper, wait for approximately five seconds, and then print five
more sheets of paper to remove any toner that may have accumulated.
Toner rubs off the page.
Make sure the Paper Type setting is correct for your print material.
Use material that is lighter than 300 g/m
2
.
Print on five sheets of paper, wait for approximately five seconds, and then print five
more sheets of paper to remove any toner that may have accumulated.
Printing shows voids.
Change the Paper Type to Plain Paper.
Print on five sheets of paper, wait for approximately five seconds, and then print five
more sheets of paper to remove any toner that may have accumulated.
Guidelines for selecting and using paper
27