LiftMaster 8165 Contractor Series User's Guide Manual - Page 10

Program the Travel, the Adjustment Button. The garage - installation

Get LiftMaster 8165 PDF manuals and user guides View all LiftMaster 8165 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Adjustment 1 Program the Travel Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. • Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system. • After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with 1-1/2" (3.8 cm) high object (or 2x4 laid flat) on floor. 1.1 Press and hold the Adjustment Button until the UP Button begins to flash and/or a beep is heard. 1.2 Press and hold the UP Button until the door is in the desired UP position. 1.3 Once the door is in the desired UP position press and release the Adjustment Button. The garage door opener lights will flash twice and the DOWN Button will begin to flash. 1.4 Press and hold the DOWN Button until the door is in the desired DOWN position. 1.5 Once the door is in the desired DOWN position press and release the Adjustment Button. The garage door opener lights will flash twice and the UP Button will begin to flash. NOTE: The UP and DOWN Buttons can be used to move the door up and down as needed. 1.6 Press and release the UP Button. When the door travels to the programmed UP position, the DOWN Button will begin to flash. 1.7 Press and release the DOWN Button. The door will travel to the programmed DOWN position. Programming is complete. 10 NOTE: The UP and DOWN Buttons can be used to move the door up and down as needed. If the garage door opener lights are flashing 5 times during the steps for Program the Travel, the programming has timed out. If the garage door opener lights are flashing 10 times during the steps for Program the Travel, the safety reversing sensors are misaligned or obstructed. When the sensors are aligned and unobstructed, cycle the door through a complete up and down cycle using the remote control or the UP and DOWN buttons. Programming is complete. If you are unable to operate the door up and down, repeat the steps for Programming the Travel.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
10
Program the Travel
1
Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a
closing garage door.
•
Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system.
•
After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with 1-1/2" (3.8 cm)
high object (or 2x4 laid flat) on floor.
1.1
Press and hold the Adjustment
Button until the UP Button begins
to flash and/or a beep is heard.
1.5
Once the door is in the desired
DOWN position press and release
the Adjustment Button. The garage
door opener lights will flash twice
and the UP Button will begin to
flash.
NOTE:
The UP and DOWN Buttons can be used
to move the door up and down as needed.
1.6
Press and release the UP Button.
When the door travels to the
programmed UP position, the
DOWN Button will begin to flash.
1.7
Press and release the DOWN
Button. The door will travel to the
programmed DOWN position.
Programming is complete.
1.4
Press and hold the DOWN Button
until the door is in the desired
DOWN position.
NOTE:
The UP and DOWN Buttons can be used
to move the door up and down as needed.
If the garage door opener lights are flashing
5 times during the steps for Program the
Travel, the programming has timed out. If
the garage door opener lights are flashing
10 times during the steps for Program the
Travel, the safety reversing sensors are
misaligned or obstructed. When the sensors
are aligned and unobstructed, cycle the
door through a complete up and down cycle
using the remote control or the UP and
DOWN buttons. Programming is complete.
If you are unable to operate the door up and
down, repeat the steps for Programming
the Travel.
Adjustment
1.3
Once the door is in the desired
UP position press and release the
Adjustment Button. The garage
door opener lights will flash twice
and the DOWN Button will begin
to flash.
1.2
Press and hold the UP Button
until the door is in the desired UP
position.