LiftMaster CSW200UL8 CSW200UL W/ SURGE SUPPRESSION & RADIO RECEIVER Manual - Page 3

Table of Contents, EMERGENCY MANUAL RELEASE - troubleshooting

Page 3 highlights

ta b l e o f c ontent s Mechanical Electrical specifications and warnings Overview and Specifications 2 Model Classification 3 Safety Installation Information 4 Gate Construction Information 5 Suggested Entrapment Protection Device Locations 6-7 Safety Precautions 8 When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them. The hazard may come from something mechanical or from electric shock. Read the warnings carefully. When you see this Signal Word on the following pages, it will alert you to the possibility of damage to your gate and/or the gate operator if you do not comply with the cautionary statements that accompany it. Read them carefully. Installation Installation Setups 9 Concrete Pad and Arm Attachment 10 Standard Installation Layout 11 Compact Installation Layout 12 Uphill Driveway Post Mounting Plate Installation 13 Gate Arm Installation 14 Output Shaft Adjustment 14 Control Board Description 15 Surge Suppressor Terminal Connections 16 IMPORTANT NOTE • BEFORE attempting to install, operate or maintain the operator, you must read and fully understand this manual and follow all safety instructions. • DO NOT attempt repair or service of your gate operator unless you are an Authorized Service Technician. wiring Earth Ground Rod Installation 17 110Vac Power Connection 18 Heater Power Connection 18 Linking Master/Second Operators 19 Solenoid/Maglock Connections 20 DC2000 Back-Up Connections 21-22 Plug-In Loop Detector Wiring 23 110Vac External Loop Detector Wiring 24 Entrapment Protection Devices (Edge Sensors 25 Entrapment Protection Devices (Non-Contact Sensors 26 adjustments Set Gate Opening Direction 27 Limit Switch Adjustments 28 Clutch Adjustment 28 Radio Receiver Programming 29-30 Setting the Timer (On, Off 31 Adjusting Reversing Sensor(s 32 OmniControl™ Board Connections 33 OFF O N Maintenance and operation Maintenance 34 Operation W4 Built-In Reset Switch 35 Audio Alarm 35 EMERGENCY MANUAL RELEASE 36 WIRING DIAGRAMS and Spec Tables 37-42 troubleshooting 43-44 repair parts 45-46 Accessories 47 installation checklist 51 WARRANTY policy 52 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56

1
• BEFORE attempting to install, operate or maintain the operator,
you must read and fully understand this manual and follow all
safety instructions.
• DO NOT attempt repair or service of your gate operator unless
you are an Authorized Service Technician.
When you see these Safety Symbols and Signal Words on the
following pages, they will alert you to the possibility of SERIOUS
INjURY or DEATH if you do not comply with the warnings that
accompany them. The hazard may come from something
mechanical or from electric shock. Read the warnings carefully.
When you see this Signal Word on the following pages, it will
alert you to the possibility of damage to your gate and/or the gate
operator if you do not comply with the cautionary statements that
accompany it. Read them carefully.
IMPORTANT NOTE
SPECIFICATIONS AND WARNINGS
Overview and Specifications
............................
2
Model Classification
..................................
3
Safety Installation Information
..........................
4
Gate Construction Information
..........................
5
Suggested Entrapment Protection Device Locations
........
6-7
Safety Precautions
...................................
8
INSTALLATION
Installation Setups
...................................
9
Concrete Pad and Arm Attachment
......................
10
Standard Installation Layout
...........................
11
Compact Installation Layout
...........................
12
Uphill Driveway Post Mounting Plate Installation
..........
13
Gate Arm Installation
................................
14
Output Shaft AdJustment
.............................
14
Control Board Description
............................
15
Surge Suppressor Terminal Connections
.................
16
WIRING
Earth Ground Rod Installation
.........................
17
110Vac Power Connection
............................
18
Heater Power Connection
.............................
18
Linking Master/Second Operators
......................
19
Solenoid/Maglock Connections
.........................
20
DC2000 Back-Up Connections
.......................
21-22
Plug-In Loop Detector Wiring
..........................
23
110Vac External Loop Detector Wiring
...................
24
Entrapment Protection Devices (Edge Sensors)
............
25
Entrapment Protection Devices (Non-Contact Sensors)
......
26
ADJUSTMENTS
Set Gate Opening Direction
............................
27
Limit Switch AdJustments
.............................
28
Clutch AdJustment
..................................
28
Radio Receiver Programming
........................
29-30
Setting the Timer (On, Off)
............................
31
AdJusting Reversing Sensor(s)
.........................
32
OmniControl™ Board Connections
......................
33
MAINTENANCE AND OPERATION
Maintenance
.......................................
34
OPERATION
Built-In Reset Switch
................................
35
Audio Alarm
.......................................
35
EMERGENCY MANUAL RELEASE
...................
36
WIRING DIAGRAMS AND SPEC TABLES
.........
37-42
TROUBLESHOOTING
...........................
43-44
REPAIR PARTS
................................
45-46
ACCESSORIES
...................................
47
INSTALLATION CHECKLIST
.......................
51
WARRANTY POLICY
..............................
52
TABLE OF CONTENTS
W4
OFF
ON
Mechanical
Electrical