LiftMaster MEGA SWING MEGA SWING - MSWDCBB Manual

LiftMaster MEGA SWING Manual

Get LiftMaster MEGA SWING PDF manuals and user guides View all LiftMaster MEGA SWING manuals
Add to My Manuals
Save this manual to your list of manuals

LiftMaster MEGA SWING manual content summary:

  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 1
    Receiver Included The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1196 www.liftmaster.com Model MSWDCBB (MEGA SWING UL) 1/2 HP COMMERCIAL DUTY SWING GATE OPERATOR OWNER'S SERVICE MANUAL THIS UNIT IS A CLASS 1, 2, 3, OR 4 SWING GATE OPERATOR FOR USE IN SWING GATE APPLICATIONS
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 2
    • BEFORE attempting to install, operate or maintain the operator, you MUST read and fully understand this manual and follow all safety instructions. • DO NOT attempt repair or service of your commercial door and gate operator unless you are an Authorized Service Technician. INSTALL THE RECEIVER Set
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 3
    out. After you have released the clamp and removed the pin, gate will be free to move manually. 2. Pull Back RED HANDLE 1. Extend 3. Press Button & parts. Description Qty. Operator 1 Accessory Shelf 1 Owner's Manual 1 Warning Signs 2 Sealed 12 Vdc, 7AH Batteries 2 Primary Arm
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 4
    security area or other restricted access locations not servicing the general public, in which unauthorized access is prevented via supervision by security personnel. SAFETY ACCESSORY SELECTION All UL325 compliant LiftMaster gate operators will accept external entrapment protection devices to
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 5
    . Swinging gates shall not open into public access areas. 7. The gate must be properly installed and work freely in both directions prior to the installation of the gate operator. 8 Controls intended for user activation must be located at least six feet (6') away from any moving part of the gate
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 6
    . • Locate entrapment protection devices to protect in BOTH the open and close gate cycles. • Locate entrapment protection devices to protect between moving gate and RIGID objects, such as posts. • A swinging gate shall NOT open into public access ways. AVERTISSEMENT ATTENTION WARNING SIGN PLACEMENT
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 7
    zone to stop the gate operator should a person enter this area. Photo beams should be installed according to their manufacturer's instructions and are to be placed in areas that pose a risk of entrapment. A separate pedestrian door is required per UL-325. On swing gates that use a contact sensor
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 8
    OVERVIEW The LiftMaster model MEGA SWING UL swing gate operator is unique in the industry. Setting the MEGA SWING UL apart are many features precision stopping at open and closed positions. • Soft start and stop in open and close travel motions. • Non-Entrapment arm design, arm does not scissor
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 9
    the 3/8" thick base as well as washers for any leveling. See drawing on page 3A. Gate Plate MEGA SWING UL Elbow 22° Proper angle for drive arm installation, do not allow arm to scissor. CONDUITS The Mega Swing UL is equipped with 1/2 and 3/4 knockout in the back of the accessory cabinet. It is
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 10
    protected. The location of the power disconnect should be returned to service. visible and clearly labeled. • Disconnecting power at the fuse box do so may result in SEVERE INJURY to persons and/or damage to operator. AC POWER HOOKUP (120/230 Vac) AVERTISSEMENT Be sure your main power
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 11
    - This input is recommended for use with our Mega Arm barrier gates. For your Mega Slide X, please use terminals 1, 2 or 3 for your free exit loop input. Terminal 8, Shadow Loop - This input operates as a hold open only when gate is a full open position. Terminals 9, 10, 11, 12 Common - These inputs
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 12
    of the second. Along with these control wires, both operators MUST share a common ground connection from chassis to chassis (or from PCB common to PCB common (Ex: master gate J5 terminal #12 to second gate J5 terminal #12) EXAMPLE: If only open and close are used at master then three wires will
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 13
    batteries get low. If batteries are low, gate will stay open after an open command is given. SWITCH 7: No longer used as of August 16, 2003. To be redefined. SWITCH 8: Not used at this time (VER 6.34 or higher only). CLOSE TIMER - SWITCH PACK S2 (1-5) On the MEGA SWING UL the switches 1-5 on S2 are
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 14
    setup). Orange Gate Open Righthand operation is viewed from the same side of the gate as the operator with the operator to your right. Operator LEFT HAND OPERATION Gate Operator Open Lefthand operation is viewed from the same side of the gate as the operator with the operator to your left
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 15
    THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following button on the hand-held remote that you wish to operate your gate. The opener will now operate when the push button on either the ADVERTENCIA receiver or the
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 16
    GENERAL SERVICE WARNING • Belt loose or needs replacement, adjust with 4 bolts that support motor to manually initiating the battery test. AVERTISSEMENT BATTERY HANDLING / STORAGE Refer to the battery manufacturer's Material Safety Data Sheets (01-30839 "MSDS Sheets, Battery, Standard"). LiftMaster
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 17
    active? Yes No Remove the active input to allow the gate to open. Remove the active input to allow the gate to close. Does the IRD light while operating? Yes Make sure the gate is not binding, then adjust the IRD. Verify the gate reverses when obstructed. No ADVERTENCIA Is the IRD flashing
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 18
    are recommended. Using the pulse contacts will REDUCE the gate's safe operation. RECOMMENDATION 2: Use safety pressure sensing edges to prevent entrapment. RECOMMENDATION 3: Install ALL access control devices within view of gate. Safety Loop Mega Swing UL Shadow Loop Card Reader Tele-entry Radio
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 19
    /Close) Safety Loop Input Close Gate Input - Close Loop Back Away - Free Exit Loop Shadow Loop Commons - 0 Vdc C18 U18 C15 Q6 Q5 Q4 D28 1 1 J2 AUX LIMITS M/S J3 R14 D8 D1Ø R18 S1 S2 1 2345678 1 2345678 R1 R12 R17 R16 MANUAL Q2 OPEN 1 2 3 4 5 6 7 8 9 1Ø 11 12 J5 S3 T2 T4 T6 T8
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 20
    Ends Nylon Washer Set Screws 17 16 Extension Tube 3 8 REAR VIEW 6 5 4 7 2 Mounting Bolt/Nut Gate Plate Arm Ends Elbow Arm Gate Plate Bolt/Nut Bolt/Nut INDIVIDUAL PARTS ITEM PART # 1 SW001 2 SW003 2 MBAT 3 SW005 4 SW006C 5 SW007 6 SW008 7 SW009 8 SW010 9 SW012 10 SW013 11 SW015 12
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 21
    7Amp Battery 2 required per operator. K1 Relay Output Option: covers and detailed instructions. Passport 4-Button open contact Miller Edge, Normally open contact Miller Edge, Normally open contact Miller Edge, Normally open contact Miller Edge, Normally open contact Miller Edge, Normally open
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 22
    service center for warranty repair. You will be advised of shipping instructions when you call. Please include a brief description of the problem . Defective parts will be repaired or replaced with new or factory-rebuilt parts at Seller CAUSED BY IMPROPER INSTALLATION, OPERATION OR CARE (INCLUDING,
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 23
    AND SERVICE INFORMATION IS AS NEAR AS YOUR TELEPHONE. SIMPLY DIAL OUR TOLL FREE NUMBER: 1-800-528-2806 www.liftmaster.com WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION: • PART NUMBER • PART NAME • MODEL NUMBER ADDRESS ORDERS TO: THE CHAMBERLAIN GROUP, INC. Technical Support Group
  • LiftMaster MEGA SWING | MEGA SWING - MSWDCBB Manual - Page 24
    and is clear on proper use of gate operator (required). _____ Customer instructed on proper use of all control devices used with operator. _____ Safety instructions were reviewed and left with customer (required). _____ Installer offered a preventative service/maintenance contract. _____ A photo of
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
Model
MSWDCBB
(MEGA SWING UL)
1/2 HP COMMERCIAL DUTY SWING GATE OPERATOR
OWNER’S SERVICE MANUAL
THIS UNIT IS A CLASS 1, 2, 3, OR 4 SWING GATE OPERATOR FOR USE IN SWING GATE APPLICATIONS
The Chamberlain Group, Inc.
845 Larch Avenue
Elmhurst, Illinois 60126-1196
www.liftmaster.com
Radio
Receiver
Included