LiftMaster T T-LOGIC 3 Manual - Page 21

PROGRAMMING 3-BUTTON REMOTE CONTROLS Your 315MHz Security✚® or dip switch remote control can be programmed to operate as a 3-button wireless control station: the large button will open the door, the middle button will close the door, and the third button will stop the door's movement. You may set up this feature as follows: 1. To enter programming press the RADIO button on the logic board (the RADIO LED will light). 2. To program the OPEN button to a remote control press the OPEN button on the logic board. The RADIO LED will flash and then stay on solid. Then press the corresponding button on the remote control. The RADIO LED on the logic board will flash, this confirms that the remote control has been programmed. (By programming the remote control you use 1 channel of the 23 channels on the radio receiver.) 3. To program the CLOSE button to a remote control press the CLOSE button on the logic board. The RADIO LED will flash and then stay on solid. Then press the corresponding button on the remote control. The RADIO LED on the logic board will flash, this confirms that the remote control has been programmed. (By programming the remote control you use 1 channel of the 23 channels on the radio receiver.) 4. To program the STOP button to a remote control, press the STOP button on the logic board. The RADIO LED will flash and then stay on solid. Then press the corresponding button on the remote control. The RADIO LED on the logic board will flash, this confirms that the remote control has been programmed. (By programming the remote control you use 1 channel of the 23 channels on the radio receiver.) 5. After learning remote controls press the RADIO button on the logic board (LED will turn off). NOTE: If no activity within 30 seconds the radio will automatically exit programming mode. OPEN Open CLOSE Close Stop STOP R31 U7 D8 U1 Ø14LGØ657-A Ø14GPØ657-A P4 C3Ø E1 C18 R29 C11 D3Ø2 X1 P1Ø C17 C25 D1 EDGE K3 D22 OPEN D2Ø POWER OLS J1 D25 J3ØØ D19 TIMER DEFEAT R8 D17 SINGLE PHASE ? CONTACTOR/3 PH ? REV? STD? CLOSE STOP D21 D13 P7 C54 C71 C78 ® MID D24 MAS D28 MOTOR DIRECTION D16 RADIO SLS D26 CLS D27 MRT MID TIMER 1 2 3 D36 RELAY A 4 D23 EYES D15 D1 EDGE D22 OPEN D2Ø TIMER ENABLE CLOSE D21 C77 C73 L1 L5 P6 RELAY B D35 T E2 D1 STOP D13 TS FSTS DIAG C2 B2 FAILSAFE SBC PROG (B2 C2 D1 E2) S8 NON FAILSAFE D14 P1 D34 D31 D7 D6 D5 D4 24V AC 14 24V AC 13 TIMER DEFEAT 12 CMN 11 MAS 10 EYES 9 EDGE 8 OPEN 7 CLOSE 6 STOP 5 CMN 4 3 2 SBC 1 F1 REMOTE CONTROL PROGRAMMING FEATURE Program Remote Controls from the 3-button control station (3BCS). Requires Firmware Version 4.6 or higher and a 3BCS with the MAS connected to the control board. This feature allows the user to add additional remote controls from the 3BCS. By default the remote control learn option is off. NOTE: Requires access to the operator electrical box to enable or disable this feature. To turn this feature on: 1. Turn the SELECTOR DIAL to PROG. 2. Press and release the RADIO button. The RADIO LED will be lit. 3. Press and release the MID button. The RADIO LED will flash quickly 6 times. 4. Press and release the RADIO button. The RADIO LED will turn off. 5. Return the SECTOR DIAL to the desired wiring type. To add remote controls from the 3BCS: 1. With the door in the fully closed position (close limit activated), press and hold STOP. 2. While holding STOP, press and hold CLOSE. 3. While holding STOP and CLOSE, press and hold OPEN. 4. Release all three buttons once the MAS LED has lit. 5. Learn a remote control by one of the following methods: a. Programming a standard single button/single function remote control, push and hold the remote control button until the MAS LED goes out. Repeat steps 1 through 4 to add additional remote controls. b. Programming a 3-button/three function remote control (open/close/stop), first push the button on the 3BCS (example: OPEN) and then press and hold the button on the remote control (example: large button) that you want to correspond with the selected (example: OPEN) command until the MAS LED flashes and goes out. Repeat steps 1 through 4 to add additional buttons (close and stop). To turn this feature off: 1. Turn the SECTOR DIAL to PROG. 2. Press and release the RADIO button. The RADIO LED will be lit. 3. Press and release the MRT button. The RADIO LED will flash quickly 3 times. 4. Press and release RADIO button. The RADIO LED will turn off. 5. Return SELECTOR DIAL to desired wiring type. NOTE: Restoring the operator to Factory Default (see "RESETTING FACTORY DEFAULTS") will also disable this feature. The remote controls will still be learned. 21