Lowrance EP-60R Fuel Flow Sensor Installation Configuration and Calibration In - Page 41

Engine Operations

Get Lowrance EP-60R Fuel Flow Sensor PDF manuals and user guides View all Lowrance EP-60R Fuel Flow Sensor manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

4. Highlight FILL TANK and press ENTER. The following confirmation message will appear: Are you sure you wish to Fill Tank? NOTE: You must use the unit's Fill Tank command when filling your fuel tank to keep the fuel flow updated with correct information on the amount of fuel in the tank. 5. Select YES and press ENTER. The following confirmation message will appear: Do you wish to re-calibrate the device? 6. Highlight NO and press ENTER. 7. Take your vessel out on the water and burn at least five gallons of fuel. Be sure you run only ONE engine - the engine connected to your fuel flow. 8. Fill up your tank again, noting how much fuel you added to the tank. Compare that number to the Fuel Used figure displayed on your display unit's screen. If the amount of fuel you added to the tank and the fuel used figure are off by more than 3 percent, we recommend the fuel flow be calibrated. To calibrate a fuel flow: 9. Fill up your tank. Press MENU twice, select NMEA 2000 or NETWORKING and press ENTER. 10. Highlight FUEL MANAGEMENT and press ENTER. Highlight TANK LOCATION and press ENTER. 11. Select the desired tank location and press ENTER. 12. Highlight FILL TANK and press ENTER. The following message will appear: Are you sure you wish to Fill Tank? Select YES and press ENTER. 13. The following message will appear: Do you wish to re-calibrate the device? Select YES and press ENTER. 14. Repeat these steps for each EP-60R Fuel Flow you want to calibrate. Engine Operations The lower half of the Fuel Management menu covers Engine Operations, which include: Engine Select, Reset Calibration, Reset Trip and Reset Seasonal. Engine Select Engine Select allows you to choose the desired engine when resetting calibration, resetting trip fuel and resetting seasonal fuel. 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
41
4. Highlight
F
ILL
T
ANK
and press
ENTER
. The following confirmation
message will appear:
Are you sure you wish to Fill Tank?
NOTE
:
You must use the unit’s Fill Tank command when filling your fuel
tank to keep the fuel flow updated with correct information on the
amount of fuel in the tank.
5. Select
Y
ES
and press
ENTER
. The following confirmation message will
appear:
Do you wish to re-calibrate the device?
6. Highlight
N
O
and press
ENTER
.
7. Take your vessel out on the water and burn at least five gallons of
fuel.
Be sure you run only ONE engine — the engine connected
to your fuel flow.
8. Fill up your tank again, noting how much fuel you added to the tank.
Compare that number to the Fuel Used figure displayed on your
display unit's screen.
If the amount of fuel you added to the tank and the fuel used figure are
off by more than 3 percent, we recommend the fuel flow be calibrated.
To calibrate a fuel flow:
9. Fill up your tank. Press
MENU
twice, select
NMEA
2000
or
N
ETWORKING
and press
ENTER
.
10. Highlight
F
UEL
M
ANAGEMENT
and press
ENTER
. Highlight
T
ANK
L
OCATION
and press
ENTER
.
11
.
Select the desired tank location and press
ENTER
.
12. Highlight
F
ILL
T
ANK
and press
ENTER
. The following message will
appear:
Are you sure you wish to Fill Tank?
Select
Y
ES
and press
ENTER
.
13. The following message will appear:
Do you wish to re-calibrate the
device? S
elect
Y
ES
and press
ENTER
.
14. Repeat these steps for each EP-60R Fuel Flow you want to
calibrate.
Engine Operations
The lower half of the Fuel Management menu covers Engine
Operations, which include: Engine Select, Reset Calibration, Reset Trip
and Reset Seasonal.
Engine Select
Engine Select allows you to choose the desired engine when resetting
calibration, resetting trip fuel and resetting seasonal fuel.