MSI MPG B550 GAMING CARBON WIFI User Manual - Page 39

JCI1: Chassis Intrusion Connector, T_SEN1: Thermal Sensor Connectors

Get MSI MPG B550 GAMING CARBON WIFI PDF manuals and user guides View all MSI MPG B550 GAMING CARBON WIFI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

JCI1: Chassis Intrusion Connector This connector allows you to connect the chassis intrusion switch cable. Normal (default) Trigger the chassis intrusion event BAT1 Using chassis intrusion detector 1. Connect the JCI1 connector to the chassis intrusion switch/ sensor on the chassis. 2. Close the chassis cover. 3. Go to BIOS > SETTINGS > Security > Chassis Intrusion Configuration. 4. Set Chassis Intrusion to Enabled. 5. Press F10 to save and exit and then press the Enter key to select Yes. 6. Once the chassis cover is opened again, a warning message will be displayed on screen when the computer is turned on. Resetting the chassis intrusion warning 1. Go to BIOS > SETTINGS > Security > Chassis Intrusion Configuration. 2. Set Chassis Intrusion to Reset. 3. Press F10 to save and exit and then press the Enter key to select Yes. T_SEN1: Thermal Sensor Connectors This connector allows you to connect the thermistor cable and use it to monitor the temperature of the detection point. BAT1 Sense GND Thermistor cable Overview of Components 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
39
Overview of Components
JCI1: Chassis Intrusion Connector
This connector allows you to connect the chassis intrusion switch cable.
BAT1
Normal
(default)
Trigger the chassis
intrusion event
Using chassis intrusion detector
1.
Connect the
JCI1
connector to the chassis intrusion switch/ sensor on the chassis.
2.
Close the chassis cover.
3.
Go to
BIOS > SETTINGS > Security > Chassis Intrusion Configuration
.
4.
Set
Chassis Intrusion
to
Enabled
.
5.
Press
F10
to save and exit and then press the
Enter
key to select
Yes
.
6.
Once the chassis cover is opened again, a warning message will be displayed on
screen when the computer is turned on.
Resetting the chassis intrusion warning
1.
Go to
BIOS > SETTINGS > Security > Chassis Intrusion Configuration
.
2.
Set
Chassis Intrusion
to
Reset
.
3.
Press
F10
to save and exit and then press the
Enter
key to select
Yes
.
BAT1
T_SEN1: Thermal Sensor Connectors
This connector allows you to connect the thermistor cable and use it to monitor the
temperature of the detection point.
Thermistor cable
GND
Sense