Mackie ART200A Quick Start Guide - Page 1

Specifications System: Freq. Range (-10 dB): 50Hz-19kHz Freq. Response (±3 dB): 70Hz-17kHz Horz. Coverage Angle (-6 dB): 90°, averaged 1kHz-10kHz Vert. Coverage Angle (-6 dB): 70°, averaged 1kHz-10kHz Directivity Factor Q (DI): 9.5 (9.8), averaged 1kHz-10kHz System Sensitivity: 101 dB, 1W@1m Rated Maximum SPL: 122 dB @ 1 m (3.3 ft) peak HF Protection: Dynamic Transducers: Low Frequency: 12" (300 mm) diameter woofer High Frequency: 1" (25 mm) compression driver, horn loaded Preamp and Processor: Input Sensitivity: Mic In: Line In: 8mV 125mV Input Impedance: Mic In: 650Ω unbalanced 1.3kΩ balanced Line In: 10kΩ unbalanced 19kΩ balanced Crossover Frequency and Slope: 1.8kHz; 24 dB/octave Time Alignment: Analog, 0.3 ms HF delay Speaker Protection: Thermal, over-excursion Music Equalization: +4.3 dB @ 65Hz +4.0 dB @ 12kHz Voice Equalization: +4.0 dB @ 3kHz +4.0 dB @ 6kHz Indicators: Power ON, Limiter Amplifiers: LF Amplifier Power: 120 watts RMS HF Amplifier Power: 40 watts RMS Distortion: < 0.1% THD at rated power Amp Protection: Thermal, limiter, short circuit Power Supply: 115/230 VAC, 2A, 50/60 Hz Physical: Enclosure: Asymmetrical trapezoidal, reinforced polypropylene Mounting: Lockable 1-3/8" (35mm) stand mount Rigging Inserts: 4 points, accepts M10 threaded hardware Input/Output Connectors: 2 XLR balanced Dimensions HxWxD: 24.4" x 15.4" x 12.3" (620 mm x 390 mm x 312 mm) Net Weight: 39.7 lb (18.0 kg) [email protected] 16220 Wood-Red Road NE Woodinville, WA 98072 TEL +888.337.7404, FAX +425.487.4337 UK +44.1268.570.808, FAX +44.1268.570.809 [email protected] ITALY +39.0522.354.111, FAX +39.0522.332.294 [email protected] FRANCE +33.3.8546.9160, FAX +33.3.8546.9161 [email protected] GERMANY +49.2572.96042.0, FAX +49.2572.96042.10 [email protected] Part No. 910-161-20 Rev. A 2/00 © 2000 Mackie Industrial. All Rights Reserved. Printed in the USA. The ART200A is a full-range two-way professional active speaker system that combines high power and wide bandwidth in a light-weight enclosure for fixed-installation systems. The 12" low-frequency transducer, in combination with a 1" compression driver coupled to an integral 90˚ x 70˚ constant directivity polynomial horn, form an extremely powerful package for any small to mediumsized sound reinforcement application. It features a balanced XLR input with a Mic/Line switch and a paralleled balanced XLR output for cascading multiple speakers. Rear panel controls also include Music and Voice equalization switches, a rotary volume control, and an input limiter. The two built-in power amplifiers provide 120W for the LF driver and 40W for the HF driver. The enclosure is constructed of highstrength polypropylene, with M10 threaded inserts on all four sides for rigging, and an integral locking 1-3/8" socket in the bottom for mounting on a standard speaker stand. ART200A Active Speaker System Quick-Start Guide Safety First! Before connecting and using the equipment, please read this Quick-Start Guide carefully and keep it for future reference. WARNING! This equipment has been designed to be installed by qualified professionals only! There are many factors to be considered when installing professional sound reinforcement systems, including mechanical and electrical considerations, as well as acoustic coverage and performance. Mackie Industrial strongly recommends that this equipment be installed only by a professional sound installer or contractor. CAUTION: To avoid the risk of electric shock, never allow this equipment to be exposed to rain or dampness. 1. Never install, connect, or disconnect the unit with the power supply on. 2. Before powering up the speaker, make sure the voltage select switch corresponds to the AC Voltage supply. 3. Make sure the safety ground on the power cord is properly grounded. 4. To prevent the risk of electric shock, never open the unit. There are no user serviceable parts inside. 5. To ensure normal cooling of the amplifier, make sure the unit is wellventilated. Avoid exposure to direct sunlight or proximity to any heat source, dust, or dampness.