Magellan RoadMate 1400 Manual - English - Page 13

Attaching the Magellan RoadMate to the Cradle, Adjust the Mount for Optimum Viewing, Connecting Power - will not power on

Page 13 highlights

Attaching the Magellan RoadMate to the Cradle Align the tabs on the cradle to the indents on the bottom of the Magellan RoadMate. Swivel the cradle up so that it is flush against the back of the receiver and snap it into place. Adjust the Mount for Optimum Viewing Loosen the adjustment locking knobs and position the Magellan RoadMate for optimum viewing. Once set, tighten the locking knobs. (Never attempt to adjust the mount while driving.) Connecting Power Plug the end of the cigarette lighter adapter into a 12 VDC vehicle power receptacle. Connect the other end of the cable to the Magellan RoadMate's USB connector as shown. If there is power at the receptacle, the Magellan RoadMate will power on. (Note: some vehicles apply power to the vehicle power receptacle only when the ignition is on.) Check Connection and Final Adjustments If the power indicator light on the vehicle power cable connector is on, power is being supplied to the Magellan RoadMate. If it is not on, check the cable connection to the vehicle power receptacle. If the light is still not on, turn the vehicle's ignition on. Press the power button (located at the bottom right side of the RoadMate) and hold down for a few seconds. The Magellan RoadMate will power on. Sit in a normal driving position and make any final adjustments to the swivel mount for optimum viewing. Tighten the adjusting knobs on the swivel mount to hold the Magellan RoadMate firmly in place. Press the power button again to turn the Magellan RoadMate off and turn the ignition switch to the vehicle to off. The Magellan RoadMate is connected and ready for use. Installation 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61

Installation
5
Attaching the Magellan RoadMate to the Cradle
Align the tabs on the cradle to the indents on the
bottom of the Magellan RoadMate.
Swivel the
cradle up so that it is flush against the back of the
receiver and snap it into place.
Adjust the Mount for Optimum Viewing
Loosen the adjustment locking knobs and position the Magellan RoadMate for optimum viewing.
Once set, tighten the locking knobs.
(Never attempt to adjust the mount while driving.)
Connecting Power
Plug the end of the cigarette lighter adapter into a
12 VDC vehicle power receptacle.
Connect the
other end of the cable to the Magellan RoadMate’s
USB connector as shown.
If there is power at the
receptacle, the Magellan RoadMate will power on.
(Note: some vehicles apply power to the vehicle
power receptacle only when the ignition is on.)
Check Connection and Final Adjustments
If the power indicator light on the vehicle power cable connector is on, power is being supplied to the
Magellan RoadMate.
If it is not on, check the cable connection to the vehicle power receptacle.
If
the light is still not on, turn the vehicle’s ignition on.
Press the power button (located at the bottom right side of the RoadMate) and hold down for a few
seconds.
The Magellan RoadMate will power on.
Sit in a normal driving position and make any final
adjustments to the swivel mount for optimum viewing.
Tighten the adjusting knobs on the swivel
mount to hold the Magellan RoadMate firmly in place.
Press the power button again to turn the Magellan RoadMate off and turn the ignition switch to the
vehicle to off.
The Magellan RoadMate is connected and ready for use.