Makita DCW180Z Instruction Manual - Page 12

4. Over-voltage protection When the input voltage is higher than the rated voltage, this protection system turns off the appliance and the temperature display shows "F4" with beep sound. 5. Short circuit protection The circuit has short circuit protection function in case of short circuit. In this situation, take the appliance to Makita Authorized or Factory Service Centers. Tilt protection function The appliance is equipped with the tilt protection function. When operating the appliance in cooling mode, the appliance will automatically shuts down if the appliance is placed under one of the following angles. A) When the appliance get equal to or greater than 30° from level angle as shown A-1 in the figure, the appliance shuts down and the temperature display shows "F1" for a while. It takes 3 minutes to restart after the appliance back in level position. When the appliance get equal to or greater than 70° from level angle as shown A-2 in the figure, the appliance shuts down and the temperature display shows "F6" until restart. It takes 2 hours to restart after the appliance back in level position. ► Fig.4 B) When the appliance get equal to or greater than 30° from level angle as shown B-1 in the figure, the appliance shuts down and the temperature display shows "F1" for a while. It takes 3 minutes to restart after the appliance back in level position. When the appliance get equal to or greater than 40° from level angle as shown B-2 in the figure, the appliance shuts down and the temperature display shows "F6" until restart. It takes 2 hours to restart after the appliance back in level position. ► Fig.5 C) When the appliance get equal to or greater than 30° from level angle as shown C-1 in the figure, the appliance shuts down and the temperature display shows "F1" for a while. It takes 3 minutes to restart after the appliance back in level position. When the appliance get equal to or greater than 70° from level angle as shown C-2 in the figure, the appliance shuts down and the temperature display shows "F6" until restart. It takes 2 hours to restart after the appliance back in level position. ► Fig.6 D) When the appliance get equal to or greater than 30° from level angle as shown D-1 in the figure, the appliance shuts down and the temperature display shows "F1" for a while. It takes 3 minutes to restart after the appliance back in level position. When the appliance get equal to or greater than 70° from level angle as shown D-2 in the figure, the appliance shuts down and the temperature display shows "F6" until restart. It takes 2 hours to restart after the appliance back in level position. ► Fig.7 E) When the appliance turns 180° from level angle, the appliance shuts down and the temperature display shows "F6" until restart. It takes 2 hours to restart after the appliance back in level position. USB charging There is the USB port in the battery compartment. The USB port continuously outputs 5V voltage in operation state. Memory function After setting the control temperature, if the user does not operate within 5 seconds, the current setting will be memorized. Next time, the appliance starts in the same setting. Switching the unit of temperature You can switch the unit of temperature °C (degree Celsius) or °F (degree Fahrenheit) by following procedure. 1. Turn on the appliance. 2. Press the cool / heat switch button until the unit (°C or °F) starts flashing. 3. Press the temperature plus button or the tempera- ture reduction button to select unit. 4. Press the cool / heat switch button, or leave the appliance 5 seconds without any operation. The unit selection is completed. Shoulder belt 1. Put the belt through left and right handles. 2. Buckle the belt. ► Fig.8 Error code For the specific errors, the temperature display shows following code. Error code F1 F2 F3 F4 F5 F6 Matter Tilt protection is active. Refer the section for the tilt protection function. Running out of battery. Input voltage is low. Refer the paragraph for the car input protection. Input voltage is high. Refer the paragraph for the overvoltage protection. Something is wrong with the sensor in the appliance. Take the appliance to Makita Authorized or Factory Service Centers. Tilt protection is active. Refer the section for the tilt protection function. 12 ENGLISH