Makita HCU02C1 Owners Manual - Page 9

Assembly

Get Makita HCU02C1 PDF manuals and user guides View all Makita HCU02C1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

malfunctioned. Contact your local Makita authorized service center. NOTE: • The indicated capacity may be lower than the actual level during use or immediately after using the tool. • Depending on the conditions of use and the ambient temperature, the indication may differ slightly from the actual capacity. ASSEMBLY 4. Remove the sprocket cover. 5. Remove the saw chain and guide bar from the chain saw. 6. To install the saw chain, fit in one end of the saw chain on the top of the guide bar and the other end of it around the sprocket. 1. Sprocket CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Installing or removing saw chain CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the saw chain. • Always wear gloves when installing or removing the saw chain. 1. To remove the saw chain, slightly slide the lever in the direction of arrow so that it can be released from the locked position and move the lever in the upright position as shown in the figure. 1. Slightly slide 1 2 2. Move in the upright position 1 010931 At this time, fit the saw chain as shown in the figure because it rotates in the direction of arrow. 7. Rest the guide bar in place on the chain saw 8. Turn the adjusting dial counterclockwise to slide the adjusting pin in the direction of arrow. 1. Adjusting pin 1 010932 9. Place the sprocket cover on the chain saw so that the adjusting pin is positioned in a small hole in the guide bar. 1. Small hole 1 011452 3 4 1. Press in 1 2. Loosen 3. Sprocket cover 2 4. Adjusting dial 010933 10. Press in the lever and with the lever depressed turn it fully clockwise to tighten the nut. Then make it about a quarter turn counterclockwise to loosen the nut lightly. 011450 2. Press the lever and with the lever pressed in, turn it counterclockwise to loosen the nut until sprocket cover comes off. (Pressing in the lever leads to the fitting of lever into the nut.) 3. Turn the adjusting dial counterclockwise to release the saw chain tension. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
9
malfunctioned.
Contact
your
local
Makita
authorized service center.
NOTE:
•
The indicated capacity may be lower than the
actual level during use or immediately after using
the tool.
•
Depending on the conditions of use and the
ambient temperature, the indication may differ
slightly from the actual capacity.
ASSEMBLY
CAUTION:
•
Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out
any work on the tool.
Installing or removing saw chain
CAUTION:
•
Always be sure that the tool is switched off and the
battery cartridge is removed before installing or
removing the saw chain.
•
Always wear gloves when installing or removing
the saw chain.
1.
To remove the saw chain, slightly slide the lever
in the direction of arrow so that it can be released
from the locked position and move the lever in the
upright position as shown in the figure.
1
2
011452
1
2
3
4
011450
2.
Press the lever and with the lever pressed in, turn
it counterclockwise to loosen the nut until
sprocket cover comes off. (Pressing in the lever
leads to the fitting of lever into the nut.)
3.
Turn the adjusting dial counterclockwise to
release the saw chain tension.
4.
Remove the sprocket cover.
5.
Remove the saw chain and guide bar from the
chain saw.
6.
To install the saw chain, fit in one end of the saw
chain on the top of the guide bar and the other
end of it around the sprocket.
1
010931
At this time, fit the saw chain as shown in the figure
because it rotates in the direction of arrow.
7.
Rest the guide bar in place on the chain saw
8.
Turn the adjusting dial counterclockwise to slide
the adjusting pin in the direction of arrow.
1
010932
9.
Place the sprocket cover on the chain saw so that
the adjusting pin is positioned in a small hole in
the guide bar.
1
010933
10.
Press in the lever and with the lever depressed
turn it fully clockwise to tighten the nut. Then
make it about a quarter turn counterclockwise to
loosen the nut lightly.
1. Small hole
1. Adjusting pin
1. Sprocket
1. Press in
2. Loosen
3. Sprocket cover
4. Adjusting dial
1. Slightly slide
2. Move in the
upright position