Makita HS0600 HS0600 Instruction Manual - Page 9

Operation

Get Makita HS0600 PDF manuals and user guides View all Makita HS0600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Connecting a vacuum cleaner Optional accessory When you wish to perform clean cutting operation, connect a Makita vacuum cleaner to your tool using the dust nozzle. 1. Replace the original lever on the tool with the one supplied with the dust nozzle. OPERATION CAUTION: Be sure to move the tool forward in a straight line gently. Forcing or twisting the tool will result in overheating the motor and dangerous kickback, possibly causing severe injury. 1 2 3 ► 1 . Original lever 2. Screw 3. Lever supplied with the dust nozzle Do not use the dust nozzle with the long lever attached. You will not be able to make a cut because the lower guard movement is hindered by the dust nozzle. 2. Install the dust nozzle on the tool using the screw. 1 2 ► 1 . Dust nozzle 2. Screw 3. Connect a hose of the vacuum cleaner to the dust nozzle. Hold the tool firmly. The tool is provided with both a front grip and rear handle. Use both to best grasp the tool. If both hands are holding saw, they cannot be cut by the circular saw blade. Set the base on the workpiece to be cut without the circular saw blade making any contact. Then turn the tool on and wait until the circular saw blade attains full speed. Now simply move the tool forward over the workpiece surface, keeping it flat and advancing smoothly until the sawing is completed. To get clean cuts, keep your sawing line straight and your speed of advance uniform. If the cut fails to properly follow your intended cut line, do not attempt to turn or force the tool back to the cut line. Doing so may bind the circular saw blade and lead to dangerous kickback and possible serious injury. Release switch, wait for circular saw blade to stop and then withdraw tool. Realign tool on new cut line, and start cut again. Attempt to avoid positioning which exposes operator to chips and wood dust being ejected from saw. Use eye protection to help avoid injury. If the front grip become loose, turn it counterclockwise to tighten. 1 ► 1 . Front grip 9 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
9
ENGLISH
Connecting a vacuum cleaner
Optional accessory
When you wish to perform clean cutting operation,
connect a Makita vacuum cleaner to your tool using the
dust nozzle.
1.
Replace the original lever on the tool with the one
supplied with the dust nozzle.
1
3
2
►
1.
Original lever
2.
Screw
3.
Lever supplied with the
dust nozzle
Do not use the dust nozzle with the long lever attached.
You will not be able to make a cut because the lower
guard movement is hindered by the dust nozzle.
2.
Install the dust nozzle on the tool using the screw.
1
2
►
1.
Dust nozzle
2.
Screw
3.
Connect a hose of the vacuum cleaner to the dust
nozzle.
OPERATION
CAUTION:
Be sure to move the tool forward
in a straight line gently.
Forcing or twisting the tool
will result in overheating the motor and dangerous
kickback, possibly causing severe injury.
Hold the tool firmly. The tool is provided with both a front
grip and rear handle. Use both to best grasp the tool.
If both hands are holding saw, they cannot be cut by
the circular saw blade. Set the base on the workpiece
to be cut without the circular saw blade making any
contact. Then turn the tool on and wait until the circular
saw blade attains full speed. Now simply move the tool
forward over the workpiece surface, keeping it flat and
advancing smoothly until the sawing is completed.
To get clean cuts, keep your sawing line straight and
your speed of advance uniform. If the cut fails to prop-
erly follow your intended cut line, do not attempt to turn
or force the tool back to the cut line. Doing so may bind
the circular saw blade and lead to dangerous kickback
and possible serious injury. Release switch, wait for cir
-
cular saw blade to stop and then withdraw tool. Realign
tool on new cut line, and start cut again. Attempt to
avoid positioning which exposes operator to chips and
wood dust being ejected from saw. Use eye protection
to help avoid injury.
If the front grip become loose, turn it counterclockwise
to tighten.
1
►
1.
Front grip