Makita TD021DSE TD021D Instruction Manual - Page 6

Assembly, Operation

Get Makita TD021DSE PDF manuals and user guides View all Makita TD021DSE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

A B B A 1 1. Switch 010329 To put on the light only, rotate the switch to the A or B side a little. To not only put on the light but also start the tool rotate the switch to the A or B side more. Release the switch to stop the lamp and tool. NOTE: • Use a dry cloth to wipe the dirt off the lens of lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination. ASSEMBLY To remove the bit, pull the sleeve in the direction of the arrow and pull the bit out firmly. NOTE: • If the bit is not inserted deep enough into the sleeve, the sleeve will not return to its original position and the bit will not be secured. In this case, try re-inserting the bit according to the instructions above. OPERATION 1 2 CAUTION: • Always be sure that the lock lever is in the locked position mark and the battery cartridge is removed before carrying out any work on the tool. Installing or removing driver bit or socket bit 12 mm (15/32") 9 mm (3/8") 001266 Use only the driver bit or socket bit shown in the figure. Do not use any other driver bit or socket bit. 1. To install the bit, pull the sleeve in the direction of the arrow and insert the bit into the sleeve as far as it will go. Then release the sleeve to secure the bit. 1. Bit 2. Sleeve 1. Straight type 2. Pistol type 010330 The tool can be used in two ways; a straight type and a pistol type which is selectable according to the conditions of workplace and screwdriving. CAUTION: • When bending the tool to use in the pistol type or straightening to use in the straight type, do not hold the bendable part of the tool. Failure to do so may cause your hand and fingers to be pinched and injured by this part. Hold the tool firmly and place the point of the driver bit in the screw head. Apply forward pressure to the tool to the extent that the bit will not slip off the screw and turn the tool on to start operation. The proper fastening torque may differ depending upon the kind or size of the screw/bolt, the material of the workpiece to be fastened, etc. The relation between fastening torque and fastening time is shown in the figures. 1 2 007509 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
6
1
A
B
A
B
010329
To put on the light only, rotate the switch to the A or B side
a little.
To not only put on the light but also start the tool rotate
the switch to the A or B side more.
Release the switch to stop the lamp and tool.
NOTE:
•
Use a dry cloth to wipe the dirt off the lens of lamp.
Be careful not to scratch the lens of lamp, or it may
lower the illumination.
ASSEMBLY
CAUTION:
•
Always be sure that the lock lever is in the locked
position
mark
and the battery cartridge is
removed before carrying out any work on the tool.
Installing or removing driver bit or socket bit
12 mm
(15/32”)
9 mm
(3/8”)
001266
Use only the driver bit or socket bit shown in the figure.
Do not use any other driver bit or socket bit.
1.
To install the bit, pull the sleeve in the direction of
the arrow and insert the bit into the sleeve as far as
it will go. Then release the sleeve to secure the bit.
1
2
007509
To remove the bit, pull the sleeve in the direction of the
arrow and pull the bit out firmly.
NOTE:
•
If the bit is not inserted deep enough into the sleeve,
the sleeve will not return to its original position and
the bit will not be secured. In this case, try
re-inserting the bit according to the instructions
above.
OPERATION
1
2
010330
The tool can be used in two ways; a straight type and a
pistol type which is selectable according to the conditions
of workplace and screwdriving.
CAUTION:
•
When bending the tool to use in the pistol type or
straightening to use in the straight type, do not hold
the bendable part of the tool. Failure to do so may
cause your hand and fingers to be pinched and
injured by this part.
Hold the tool firmly and place the point of the driver bit in
the screw head. Apply forward pressure to the tool to the
extent that the bit will not slip off the screw and turn the
tool on to start operation.
The proper fastening torque may differ depending upon
the kind or size of the screw/bolt, the material of the
workpiece to be fastened, etc. The relation between
fastening torque and fastening time is shown in the
figures.
1. Straight type
2. Pistol type
1. Bit
2. Sleeve
1. Switch