Makita XRU15PT XRU15 Instruction Manual - Page 4
Never climb up into trees to perform cutting
View all Makita XRU15PT manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
9. Do not expose a battery pack or machine to fire or excessive temperature. Exposure to fire or temperature above 130°C (265°F) may cause explosion. 10. Follow all charging instructions and do not charge the battery pack or machine outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire. 11. Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained. 12. Do not modify or attempt to repair the machine or the battery pack except as indicated in the instructions for use and care. 13. Do not dispose of the battery(ies) in a fire. The cell may explode. Check with local codes for possible special disposal instructions. 14. Do not open or mutilate the battery(ies). Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed. 15. Do not charge battery in rain, or in wet locations. Starting up the tool 1. Make sure that there are no children or other people within a working range of 15 meters (50 ft), also pay attention to any animals in the working vicinity. Otherwise stop using the tool. 2. Before use always check that the tool is safe for operation. Check the security of the nylon cutting head and the guard and the switch trigger/lever for easy and proper action. Check for clean and dry handles and test the on/off function of the switch. 3. Check damaged parts before further use of the tool. A guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other condition that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by our authorized service center unless indicated elsewhere in this manual. 4. Switch on the motor only when hands and feet are away from the nylon cutting head. 5. Before starting make sure that the nylon cutting head has no contact with hard objects such as branches, stones etc. as the nylon cutting head will revolve when starting. 6. Remove any adjusting key, wrench or blade cover before turning the power tool on. An accessory left attached to a rotating part of the power tool may result in personal injury. 7. Make sure there are no electrical cables, water pipes, gas pipes etc. that could cause a hazard if damaged by use of the tool. 8. Do not use a cutting tool which is not recommended by Makita. Method of operation 1. Only use the tool in good light and visibility. During the winter season beware of slippery or wet areas, ice and snow (risk of slipping). Always ensure a safe footing. 2. Take care against injury to feet and hands from the nylon cutting head. 3. Never cut above waist height. 4. Never stand on a ladder and run the tool. 5. Never climb up into trees to perform cutting operation with the tool. 6. Never work on unstable surfaces. 7. Remove sand, stones, nails etc. found within the working range. Foreign particles may damage the nylon cutting head. 8. Should the nylon cutting head hit stones or other hard objects, immediately switch off the motor and inspect the nylon cutting head. 9. Before commencing cutting, the nylon cutting head must have reached full working speed. 10. During operation always hold the tool with both hands. Never hold the tool with one hand during use. Always ensure a safe footing. 11. The nylon cutting head has to be equipped with the guard. Never run the tool with damaged guards or without guards in place! 12. All protective equipment such as guards supplied with the string trimmer must be used during operation. 13. Except in case of emergency, never drop or cast the tool to the ground or this may severely damage the tool. 14. Never drag the tool on the ground when moving from place to place, the tool may become damaged if moved in this manner. 15. Always remove the battery cartridge from the tool: - whenever leaving the tool unattended; - before clearing a blockage; - before checking, cleaning or working on the tool; - whenever the tool starts vibrating abnormally; - whenever transporting the tool. 16. Always ensure that the ventilation openings are kept clear of debris. 4 ENGLISH