Makita XSL05Z XSL05 Instruction Manual - Page 13

Small sub-fence

Page 13 highlights

1 ► 1 . Sub-fence When performing cuts except for bevel cuts, use the sub-fence to support the workpiece. Small sub-fence CAUTION: When performing right bevel cuts, fold the small sub-fences. Otherwise, they may contact the blade or a part of the tool, and may result in serious injury to the operator. 1 1. Loosen the fixing screw counterclockwise. 2. Adjust the angle of the turn base. Use the pointer and the miter scale as a guide. 3. Tighten the fixing screw clockwise firmly. CAUTION: After changing the miter angle, always secure the turn base by tightening the fixing screw firmly. NOTICE: When turning the turn base, be sure to raise the handle fully. Adjusting the bevel angle To adjust the bevel angle, turn the lever at the rear of the tool downward. 2 ► 1 . Small sub-fence 2. Scale This tool is equipped with the small sub-fences. When performing vertical cut or left bevel cut, flip them upward to support the workpiece. The guide fence has a scale of 12.7 mm (1/2") interval. Adjusting the miter angle 1 ► 1 . Lever To tilt the blade to the left, hold the handle and tilt the saw head. Use the bevel scale and the pointer as a guide. Then turn the lever upward firmly to secure the saw head. 1 2 1 ► 1 . Pointer 2. Bevel scale To tilt the blade to the right, hold the handle and tilt the saw head to the left slightly, and push the release but- ton. With the release button pressed, tilt the saw blade 4 to the right. Turn the lever upward firmly to secure the saw head. 2 3 ► 1 . Fixing screw 2. Turn base 3. Miter scale 4. Pointer 13 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52

13
ENGLISH
1
1.
Sub-fence
When performing cuts except for bevel cuts, use the
sub-fence to support the workpiece.
Small sub-fence
CAUTION:
When performing right bevel cuts,
fold the small sub-fences.
Otherwise, they may
contact the blade or a part of the tool, and may result
in serious injury to the operator.
1
2
1.
Small sub-fence
2.
Scale
This tool is equipped with the small sub-fences. When
performing vertical cut or left bevel cut, flip them upward
to support the workpiece. The guide fence has a scale
of 12.7 mm (1/2") interval.
Adjusting the miter angle
1
2
3
4
1.
Fixing screw
2.
Turn base
3.
Miter scale
4.
Pointer
1.
Loosen the fixing screw counterclockwise.
2.
Adjust the angle of the turn base. Use the pointer
and the miter scale as a guide.
3.
Tighten the fixing screw clockwise firmly.
CAUTION:
After changing the miter angle,
always secure the turn base by tightening the
fixing screw firmly.
NOTICE:
When turning the turn base, be sure to
raise the handle fully.
Adjusting the bevel angle
To adjust the bevel angle, turn the lever at the rear of
the tool downward.
1
1.
Lever
To tilt the blade to the left, hold the handle and tilt the
saw head. Use the bevel scale and the pointer as a
guide. Then turn the lever upward firmly to secure the
saw head.
1
2
1.
Pointer
2.
Bevel scale
To tilt the blade to the right, hold the handle and tilt the
saw head to the left slightly, and push the release but-
ton. With the release button pressed, tilt the saw blade
to the right. Turn the lever upward firmly to secure the
saw head.