Marantz NR1504 Owner's Manual in English - Page 136

Audio, FM/AM, Symptom, Cause/Solution

Get Marantz NR1504 PDF manuals and user guides View all Marantz NR1504 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 136 highlights

Basic instructions Advanced instructions GAudioH Symptom Cause/Solution Page Audio is not output. • Check the connections for all devices. 9, 10, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 82 • Check the speaker connections and configurations. 81 • Check whether the audio device power is turned on. - • Adjust the master volume. 31 • Cancel the mute mode. 31 • Check the connection with the playback device and select the 30 proper input source. • Match the input mode and the terminal assigned to be the digital 105 input terminal. • Disconnect the headphones. No sound is output from the 120 speakers when headphones are connected. The volume does not • The maximum volume is set too low. Set the maximum volume 96 increase. using "Limit"on the menu. • Power for external devices connected to the output connectors - of the unit may not be turned on. Check the power of connected external devices. No sound is • Check if the surround speakers are connected to the SURROUND - produced from terminals. surround speakers. No sound is produced from subwoofer. • Check the subwoofer connections. • Turn on the subwoofer's power. • Set "Speaker Config." - "Subwoofer" on the menu to "Yes". • If "Front" and "Center" for "Speaker Config." are set to "Large", and "Subwoofer Mode" is set to "LFE", no sound may be output from the subwoofers, depending on the input signal or selected sound mode. 81 - 107 107, 109 DTS sound is not • Set "Decode Mode" on the menu to "Auto" or "DTS". 105 output. Dolby TrueHD, DTSHD, Dolby Digital Plus audio is not output. • Make HDMI connections. 9, 10 Symptom Cause/Solution Dolby PLg mode or DTS NEO:6 mode cannot be selected. Audyssey MultEQ®, Audyssey Dynamic EQ® and Audyssey Dynamic Volume® cannot be selected. Audyssey Dynamic EQ® and Audyssey Dynamic Volume® cannot be selected. "M-DAX" cannot be selected. • Check that "Speaker Config." - "Center" or "Surround" is set to other than "None". If the speaker system is 2.0/2.1-channel, this sound mode cannot be selected. • When headphones are used, Dolby PLg or DTS NEO:6 cannot be selected. • Switch the sound mode to other than "DIRECT" or "PURE DIRECT". • When headphones are used, Audyssey MultEQ®, Audyssey Dynamic EQ® and Audyssey Dynamic Volume® cannot be selected. • Run Audyssey® Setup. • Check that an analog signal or PCM signal (Sample Rate=44.1/48 kHz) is input. For playback of multichannel signals such as Dolby Digital or DTS surround, "M-DAX" cannot be used. • Switch the sound mode to other than "DIRECT" or "PURE DIRECT". GFM/AMH Symptom Cause/Solution Reception fails, or there is a lot of noise or distortion. • Change the antenna orientation or position. • Separate the AM loop antenna from the unit. • Use an FM outdoor antenna. • Separate the antenna from other connection cables. Page 107 - 72 - 23 96 72 Page 19 19 19 19 Information 133 DVD

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
133
G
Audio
H
Symptom
Cause/Solution
Page
Audio is not output.
•
Check the connections for all devices.
•
Check the speaker connections and configurations.
•
Check whether the audio device power is turned on.
•
Adjust the master volume.
•
Cancel the mute mode.
•
Check the connection with the playback device and select the
proper input source.
•
Match the input mode and the terminal assigned to be the digital
input terminal.
•
Disconnect the headphones. No sound is output from the
speakers when headphones are connected.
9
, 
10
, 
13
, 
14
,
15
, 
16
, 
17
, 
18
,
19
, 
20
, 
21
, 
22
,
82
81
–
31
31
30
105
120
The volume does not
increase.
•
The maximum volume is set too low. Set the maximum volume
using “Limit”on the menu.
•
Power for external devices connected to the output connectors
of the unit may not be turned on. Check the power of connected
external devices.
96
–
No sound is
produced from
surround speakers.
•
Check if the surround speakers are connected to the SURROUND
terminals.
–
No sound is
produced from
subwoofer.
•
Check the subwoofer connections.
•
Turn on the subwoofer’s power.
•
Set “Speaker Config.” – “Subwoofer” on the menu to “Yes”.
•
If “Front” and “Center” for “Speaker Config.” are set to “Large”,
and “Subwoofer Mode” is set to “LFE”, no sound may be output
from the subwoofers, depending on the input signal or selected
sound mode.
81
–
107
107
,
109
DTS sound is not
output.
•
Set “Decode Mode” on the menu to “Auto” or “DTS”.
105
Dolby TrueHD, DTS-
HD, Dolby Digital
Plus audio is not
output.
•
Make HDMI connections.
9
,
10
Symptom
Cause/Solution
Page
Dolby PL
g
mode or
DTS NEO:6 mode
cannot be selected.
•
Check that “Speaker Config.” – “Center” or “Surround” is set to
other than “None”. If the speaker system is 2.0/2.1-channel, this
sound mode cannot be selected.
•
When headphones are used, Dolby PL
g
or DTS NEO:6 cannot be
selected.
107
–
Audyssey MultEQ
®
,
Audyssey Dynamic
EQ
®
and Audyssey
Dynamic Volume
®
cannot be selected.
•
Switch the sound mode to other than “DIRECT” or “PURE
DIRECT”.
•
When headphones are used, Audyssey MultEQ
®
, Audyssey
Dynamic EQ
®
and Audyssey Dynamic Volume
®
cannot be selected.
72
–
Audyssey Dynamic
EQ
®
and Audyssey
Dynamic Volume
®
cannot be selected.
•
Run Audyssey
®
Setup.
23
“M-DAX” cannot be
selected.
•
Check that an analog signal or PCM signal (Sample Rate=44.1/48
kHz) is input. For playback of multichannel signals such as Dolby
Digital or DTS surround, “M-DAX” cannot be used.
•
Switch the sound mode to other than “DIRECT” or “PURE
DIRECT”.
96
72
G
FM/AM
H
Symptom
Cause/Solution
Page
Reception fails, or
there is a lot of noise
or distortion.
•
Change the antenna orientation or position.
•
Separate the AM loop antenna from the unit.
•
Use an FM outdoor antenna.
•
Separate the antenna from other connection cables.
19
19
19
19