Marantz RC3001 User Guide - Page 18

Setting The Group Id Selector

Get Marantz RC3001 PDF manuals and user guides View all Marantz RC3001 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

ENGLISH SETTING THE GROUP ID SELECTOR The RC3001 can use the Wizz.it 3 editor to set the group ID for each device. If a different ID signal is sent from the remote controller, no control signal is output from the RX3001. Normally, set to lID1z when not using the group ID function. Group ID 1 Receiver side Emitter Output 1 2 3 4 5 6 Set ID 1 Set ID 1 Set ID 1 Set ID 1 Set ID 1 Set ID 1 ID Group ID 2 Receiver side Emitter Output 1 2 3 4 5 6 Set ID 1 Set ID 1 Set ID 1 Set ID 2 Set ID 2 Set ID 2 12 Output from the Output jack is controlled as shown below based on the remote device ID setting and receiver ID setting. Remote device ID Receiver GROUP ID GROUP ID SW 1 1 GROUP ID GROUP ID SW 2 1 GROUP ID GROUP ID SW 2 2 GROUP ID GROUP ID SW 1 2 Emitter Output 1 2 3 4 5 6 Emitter Output 1 2 3 4 5 6 Emitter Output 1 2 3 4 5 6 Emitter Output 1 2 3 4 5 6 OUTPUT signal OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT signal NO-OUT NO-OUT NO-OUT NO-OUT NO-OUT NO-OUT OUTPUT signal NO-OUT NO-OUT NO-OUT OUTPUT OUTPUT OUTPUT OUTPUT signal OUTPUT OUTPUT OUTPUT NO-OUT NO-OUT NO-OUT 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
13
ENGLISH
SETTING THE GROUP ID SELECTOR
The RC3001 can use the Wizz.it 3 editor to set the group ID for each device.
If a different ID signal is sent from the remote controller, no control signal is output from the RX3001.
Normally, set to
“
ID1
”
when not using the group ID function.
Receiver side
Group ID
Emitter Output
1
1
Set ID 1
2
Set ID 1
3
Set ID 1
4
Set ID 1
5
Set ID 1
6
Set ID 1
Receiver side
Group ID
Emitter Output
2
1
Set ID 1
2
Set ID 1
3
Set ID 1
4
Set ID 2
5
Set ID 2
6
Set ID 2
Output from the Output jack is controlled as shown below based on the remote device ID setting and
receiver ID setting.
Remote device ID
Receiver
GROUP ID
GROUP ID SW
Emitter Output
OUTPUT signal
1
1
1
OUTPUT
2
OUTPUT
3
OUTPUT
4
OUTPUT
5
OUTPUT
6
OUTPUT
GROUP ID
GROUP ID SW
Emitter Output
OUTPUT signal
2
1
1
NO-OUT
2
NO-OUT
3
NO-OUT
4
NO-OUT
5
NO-OUT
6
NO-OUT
GROUP ID
GROUP ID SW
Emitter Output
OUTPUT signal
2
2
1
NO-OUT
2
NO-OUT
3
NO-OUT
4
OUTPUT
5
OUTPUT
6
OUTPUT
GROUP ID
GROUP ID SW
Emitter Output
OUTPUT signal
1
2
1
OUTPUT
2
OUTPUT
3
OUTPUT
4
NO-OUT
5
NO-OUT
6
NO-OUT
12
ID