Marantz SR6003 SR6003 User Manual - English - Page 71

Basic Operation Remote Controller - av

Get Marantz SR6003 PDF manuals and user guides View all Marantz SR6003 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

NAMES AND FUNCTION BASIC CONNECTIONS BASIC OPERATION ENGLISH BASIC OPERATION (REMOTE CONTROLLER) NORMAL MODE (When operating Marantz AV equipment products) This remote controller is preset with a total of 12 types of remote codes, including Marantz TV (television), DVD, VCR (VCR deck), DSS (satellite broadcasting tuner), TUNER, CD, CD-R, DMP, TAPE (tape deck), AUX1, AUX2, and AMP (amplifier). Learning is not necessary for Marantz products. You can use these products without setting any codes. 1. Press the SOURCE button. For this example, press DVD. Pressing the SOURCE button once changes the remote control to the settings for the source that was pressed. To change the amplifier on other source, press the SOURCE button twice (double-click). The code is sent, and then the amplifier source changes to DVD. SETTING THE BACK LIGHT Pressing the Light button located on the side of the remote controller lights the remote controller's backlight. Pressing the button again while the backlight is lit lights the backlight for another 2 seconds. To turn off back light, press and hold down the SET and OFF button until indicator blinks twice. To turn on it again, press and hold down the SET and ON button until indicator blinks twice. Initial is back light ON. PRESET MODE (When operating non-Marantz AV equipment products) This remote controller is preset with remote control codes from AV equipment by other manufacturers. The preset codes are TV, CD, DVD and DSS. Settings can be made in one of two ways. When the preset codes are set, the following codes are contained in the source button of the remote controller. See the attached manufacturer number list for the preset manufacturers, devices, preset numbers, and other settings. Remote controller source name TV DVD CD DSS Corresponding preset Device name code TV Television DVD DVD player CD CD player SATELLITE Satellite broadcasting tuner equipment Importants: • Some codes may be not match your equipment. In this case, you can use LEARN mode to store these codes. • The preset codes do not cover full functions. If you need extra function, use LEARN mode to store extra function. • When the batteries are getting weak, the preset procedure is not successful. PROGRAMMING WITH THE 4-DIGIT CODE 1. 2. 1. 1. Press and hold down the SOURCE button for the appliance which should be controlled and press SET button until the indicator blinks twice. Then back light flushes. 2. Press the 4-digit code by numeric buttons for appliance (code table at the end of this book) Display 4-digit code on the LCD. When the procedure is successful, "OK" is displayed on the LCD. Note: If "NG" is displayed on the LCD, then repeat steps 1 through 2 and try entering the same code again. SCANNING THE CODE TABLE 2. 3. 2. 3. 5. 1. Switch on the appliance which should be controlled. 2. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the indicator blinking twice. Then back light flushes. 3. Aim the remote control at the appliance and slowly alternate between pressing INPUT 3 button and the SOURCE ON/OFF button for the appliance. Display the setup number on the LCD. 4. Stop when the appliance turns off. 5. Press ENTER button once to lock in the code. ADVANCED CONNECTIONS SETUP ADVANCED OPERATION TROUBLESHOOTING OTHERS 68

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
68
ENGLISH
BASIC
CONNECTIONS
BASIC OPERATION
ADVANCED
CONNECTIONS
SETUP
ADVANCED
OPERATION
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTION
ADVANCED
OPERATION
BASIC OPERATION (REMOTE CONTROLLER)
NORMAL MODE
(
When operating Marantz AV equipment products
)
This remote controller is preset with a total of 12 types
of remote codes, including Marantz TV (television),
DVD, VCR (VCR deck), DSS (satellite broadcasting
tuner), TUNER, CD, CD-R, DMP, TAPE (tape deck),
AUX1, AUX2, and AMP (amplifier).
Learning is not necessary for Marantz products. You
can use these products without setting any codes.
1.
Press the
SOURCE
button.
For this example, press DVD.
Pressing the
SOURCE
button once changes
the remote control to the settings for the source
that was pressed.
To change the amplifier on other source, press
the
SOURCE
button twice (double-click). The
code is sent, and then the amplifier source
changes to DVD.
SETTING THE BACK LIGHT
Pressing the Light button located on the side of
the remote controller lights the remote controller’s
backlight. Pressing the button again while the backlight
is lit lights the backlight for another 2 seconds.
To turn off back light, press and hold down the
SET
and
OFF
button until
indicator blinks twice.
To turn on it again, press and hold down the
SET
and
ON
button until
indicator blinks twice.
Initial is back light ON.
PRESET MODE
(When operating non-Marantz AV equipment
products)
This remote controller is preset with remote control
codes from AV equipment by other manufacturers.
The preset codes are TV, CD, DVD and DSS. Settings
can be made in one of two ways.
When the preset codes are set, the following codes
are contained in the source button of the remote
controller.
See the attached manufacturer number list for the
preset manufacturers, devices, preset numbers, and
other settings.
Remote controller
source name
Corresponding preset
code
Device name
TV
TV
Television
DVD
DVD
DVD player
CD
CD
CD player
DSS
SATELLITE
Satellite broadcasting
tuner equipment
Importants:
• Some codes may be not match your equipment.
In this case, you can use LEARN mode to store these
codes.
• The preset codes do not cover full functions.
If you need extra function, use LEARN mode to
store extra function.
• When the batteries are getting weak, the preset
procedure is not successful.
PROGRAMMING WITH THE 4-DIGIT CODE
1.
1.
2.
1.
Press and hold down the
SOURCE
button for the
appliance which should be controlled and press
SET
button until the
indicator blinks twice. Then
back light flushes.
2.
Press the 4-digit code by
numeric
buttons for
appliance (code table at the end of this book)
Display 4-digit code on the LCD.
When the procedure is successful, “OK” is
displayed on the LCD.
Note:
If “NG” is displayed on the LCD, then repeat steps 1
through 2 and try entering the same code again.
SCANNING THE CODE TABLE
2.
3.
5.
2.
3.
1.
Switch on the appliance which should be
controlled.
2.
Press and hold down the
SOURCE
button for
appliance which should be controlled and press
SET
button until the
indicator blinking twice.
Then back light flushes.
3.
Aim the remote control at the appliance and
slowly alternate between pressing
INPUT
3
button and the
SOURCE ON/OFF
button for the
appliance.
Display the setup number on the LCD.
4.
Stop when the appliance turns off.
5.
Press
ENTER
button once to lock in the code.