Marantz SR9600XM SR9600XM User Manual - Page 5

ENGLISH PRESET MEMORY AV SURROUND RECEIVER SR9600 You can store the desired channel in the Preset Memory. 3. 2. 4. wed Jun 01 4:40pm 2/2 XM XM : Key INPUT SELECTOR PURE DIRECT THX DOWN TUNING UP VOLUME 3. DOWN UP BAND F/P NDBY N/STANDBY PHONES SURROUND MODE AUTO MULTI MULTI SPEAKER AUTO TUNE T-MODE MEMORY CLEAR PURE DIRECT THX 7.1CH INPUT MENU ENTER DISPLAY EXIT MRAC SPEAKERS A/B MIC 2. DIGITAL AUX 1 INPUT S-VIDEO VIDEO L AUDIO R (Using the SR9600) 1. Tune into the desired channel. 2. Press the MEMORY button on the front panel. "PRESET - -" (preset number) starts blinking on the display. 3. Select the preset number by rotating the GYRO TUNING dial, while it is still blinking (approx. 5 second) 4. Press the MEMORY button again to enter. The display stops blinking. The Channel is now stored in the specified preset memory location. (Using the remote control unit) 1. Tune into the desired channel. 2. Tap the Memo on the remote control unit. "PRESET - -" (preset number) starts blinking on the display. 3. Enter the desired preset number by tapping the numeric keypads. CHECKING THE PRESET CHANNEL The preset channel can be checked on the on screen display. wed Jun 01 4:40pm 1/2 XM XM : Main 1. 2. (Using the remote control unit) 1. Tap the Info. to view a list of tuner preset channel on the on screen display. 2. If there are 10 or more preset channel, tap the Info. again. TUNER PRESET L I ST NO . NO . NO . NO . NO . NO . NO . NO . NO . 1 XM0 0 1 P r e v i ew 2 XM0 0 1 P r e v i ew 3 XM0 0 1 P r e v i ew 4 XM0 0 1 P r e v i ew 5 XM0 0 1 P r e v i ew 6 XM0 0 1 P r e v i ew 7 XM0 0 1 P r e v i ew 8 XM0 0 1 P r e v i ew 9 XM0 0 1 P r e v i ew Note • The preset channel indication disappears in about 5 sec. PRESET SCAN wed Jun 01 4:40pm 1/2 XM XM : Main CLEARING STORED PRESET STATIONS You can remove preset stations from the memory using the following procedure. 3. AV SURROUND RECEIVER SR9600 2. 3. wed Jun 01 4:40pm 2/2 XM XM : Key 1. 3. INPUT SELECTOR STANDBY wed Jun 01 4:40pm POWER ON/STANDBY PHONES 2/2 XM XM : Key VOLUME PURE DIRECT THX DOWN TUNING UP BAND F/P SURROUND MODE AUTO MULTI MULTI SPEAKER AUTO TUNE T-MODE MEMORY CLEAR PURE DIRECT THX 7.1CH INPUT MENU ENTER DISPLAY EXIT MRAC SPEAKERS A/B MIC DOWN UP 2. DIGITAL AUX 1 INPUT S-VIDEO VIDEO L AUDIO R 3. 1. Recall the preset number to be cleared with the method described in "RECALLING A PRESET CHANNEL". 3. 2. Press the MEMORY button on the front panel or tap the Memo on the remote control unit. (Using the remote control unit) 1. Tap the P-Scan on the remote control unit. "PRESET SCAN" appears on the display and then the preset station with the lowest preset number is recalled first. 2. Preset stations are recalled in sequence (No. 1→ No. 2→ etc.) for about 5-10 seconds each. The time changes by the received condition. No stored preset number will be skipped. 3. You can fast forward through the Preset stations by tapping the Preset continuously. When the desired preset station is received, cancel the preset scan operation by tapping the CLR or P-Scan. 3. The stored preset number blinks in the display for 5 seconds. While blinking, press the CLEAR button on the front panel or tap the CLR on the remote control unit. 4. "xx CLEAR" appears on the display to indicate that the specified preset number has been cleared. Note • To clear all stored preset channels, press and hold the CLEAR and the F/P buttons for two seconds. • There are 50 preset channels prepared at the factory default. The 50 channels are all set to "CHANNEL 001". Each channel can be stored in the preset memory. You can search for only the preset channels. Note • When entering a single digit number (2 for example), either input "02" or just input "2" and wait for a few seconds. 5