Maytag MEDB955FW Installation Guide - Page 22

Reverse Door Swing - door reversal kit

Get Maytag MEDB955FW PDF manuals and user guides View all Maytag MEDB955FW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

REVERSE DOOR SWING Tools needed: 4. R emove the dryer door from the cabinet by lifting upward and out. Lay the door on a towel or a soft cloth you placed on a flat workspace. Plastic putty knife Min. 8" long TORX T20® † screwdriver #2 Phillips screwdriver Optional Assembly Kit Covers You can change your door swing from a right-hinge opening to a left-hinge opening, if desired. NOTE: To complete the door swing reversal exactly as seen in these instructions, a door reversal kit must be purchased. For ordering information, please reference the Use and Care Guide. 1. Place a towel or soft cloth on a flat workspace such as a floor to avoid damaging the dryer's surface or the dryer door. Remove door from dryer cabinet 1. Open the dryer door. 2. Use a plastic putty knife to remove the hinge covers and plastic covers from the front panel of the dryer. Set them aside. 5. U se a plastic putty knife to remove the door hinge covers. Set them aside. 6. Using a #2 Phillips screwdriver, remove the remaining 4 screws from the hinges. Then remove hinges A and B and set both the screws and hinges aside. A 3. Using a T20®† screwdriver, remove screws (A) and then screws (B) from each of the 2 hinges attaching the dryer door to the front panel of the dryer. Set the hinge screws off to the side for use in reinstalling the door. B B A B A † ® TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
22
REVERSE DOOR SWING
You can change your door swing from a right-hinge opening
to a left-hinge opening, if desired.
NOTE:
To complete the door swing reversal exactly as seen in
these instructions, a door reversal kit must be purchased. For
ordering information, please reference the Use and Care Guide.
1.
Place a towel or soft cloth on a flat workspace such as a floor
to avoid damaging the dryer’s surface or the dryer door.
Remove door from dryer cabinet
1.
Open the dryer door.
2.
Use a plastic putty knife to remove the hinge covers and
plastic covers from the front panel of the dryer. Set them aside.
4.
Remove the dryer door from the cabinet by lifting upward
and out. Lay the door on a towel or a soft cloth you placed
on a flat workspace.
5.
Use a plastic putty knife to remove the door hinge covers.
Set them aside.
6.
Using a #2 Phillips screwdriver, remove the remaining 4 screws
from the hinges. Then remove hinges A and B and set both the
screws and hinges aside.
Tools needed:
Min. 8" long TORX T20
® †
screwdriver
Plastic putty knife
#2 Phillips screwdriver
B
A
3.
Using a T20
®†
screwdriver, remove screws (A) and then
screws (B) from each of the 2 hinges attaching the dryer
door to the front panel of the dryer. Set the hinge screws
off to the side for use in reinstalling the door.
B
A
B
A
Optional Assembly Kit
Covers
†
® TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.