Maytag MHWE250XL Owners Manual - Page 4
Options, Location Requirements - pedestal
UPC - 883049216782
View all Maytag MHWE250XL manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
Alternate Parts Your installation may require additional parts. If you are interested in purchasing one of the items listed here, call the toll-free number on the cover or in the "Assistance or Service" section. If You Have You Will Need to Buy Laundry tub or standpipe taller than 96" (2.4 m) Sump pump system (if not already available) Overhead sewer Standard 20 gal. (76 L), 30" (762 mm) tall drain tub or utility sink and sump pump (available from local plumbing suppliers) Floor drain Siphon break, Part Number 285834; additional drain hose Part Number 8318155; and connector kit, Part Number 2858835 Drain hose too short 4 ft. (1.2 m) drain hose extension kit, Part Number 2858863 Water faucets beyond reach of fill hoses 2 longer inlet hoses: 5ft ( 1.5 m) Black EPDM (2 pack) 8212641RP, 10 ft ( 3.0 m) Black EPDM (2 pack) 8212656RP Options Pedestal You have the option of purchasing pedestals of different heights separately for this washer. You may select a 10" (254 mm) or a 15.5" (394 mm) pedestal. The pedestal will add to the total height of the washer. Location Requirements Selecting the proper location for your washer improves performance and minimizes noise and possible washer "walk." Your washer can be installed under a custom counter, or in a basement, laundry room, closet, or recessed area. See "Drain System." Companion appliance location requirements should also be considered. Proper installation is your responsibility. You will need: ■ A water heater set to deliver 120°F (49°C) water to the washer. ■ A grounded electrical outlet located within 6 ft. (1.8 m) of where the power cord is attached to the back of the washer. See "Electrical Requirements." ■ Hot and cold water faucets located within 4 ft. (1.2 m) of the hot and cold water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa). ■ A level floor with a maximum slope of 1" (25 mm) under entire washer. Installing the washer on soft floor surfaces, such as carpets or surfaces with foam backing, is not recommended. ■ A sturdy and solid floor to support the washer with a total weight (water and load) of 400 lbs (180 kg). Do not operate your washer in temperatures below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. Installation clearances ■ The location must be large enough to allow the washer door to be fully opened. ■ Additional spacing should be considered for ease of installation and servicing. The door opens more than 90°, and it is not reversible. ■ Additional clearances might be required for wall, door, and floor moldings. ■ Additional spacing of 1" (25 mm) on all sides of the washer is recommended to reduce noise transfer. ■ Companion appliance spacing should also be considered. Washer Dimensions 501/4" (1276 mm) 27" (686 mm) Optional pedestal Pedestal Height Approximate Height with Washer Color Model Number 10" (254 mm) 46" (1168 mm) White WHP1000SQ 15.5" (394 mm) 51.5" (1308 mm) White WHP1500SQ 15.5" (394 mm) 51.5" (1308 mm) Lunar XHP1550WL Silver Stack Kit Are you planning to stack your washer and dryer? To do so you will need to purchase a Stack Kit. To order, call the dealer from whom you purchased your washer or refer to the "Assistance or Service" section. Ask for Part Number 8572546. 36" (914 mm) 301/2" (775 mm) 4
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52