McAfee DTP-165C-DPVG Installation Guide - Page 15

Time Configuration, Manual, Policy Activation, Administrator Setup, Email and Email Server Setting

Get McAfee DTP-165C-DPVG - Network DLP Prevent 1650 Appliance PDF manuals and user guides View all McAfee DTP-165C-DPVG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Setting up the hardware Configure McAfee DLP Manager 2 Task 1 On the Time Configuration page, change the time zone. 2 Select Manual to set NTP to local time. On this first configuration, you will not yet be able to set the NTP server because the default IP address (192.168.1.2) will not allow it to be located. The NTP server can be defined only when the system is restarted and integrated into the network. 3 On the Policy Activation page, select the checkboxes of the policies that will generate incidents that are relevant to your protection strategy. If you are in a region that is not listed, you will be able to activate policies that are directly relevant to your location after the system is installed. 4 On the Administrator Setup page, enter the email address of the primary administrator and change the password from the default. 5 On the Email and Email Server Setting page, enter the IP address or host name of the email server. 6 On the Review page, verify your settings, click Cancel, or click Previous to change them. 7 When you have confirmed your settings, click Submit, then Exit Wizard. At this point, the McAfee DLP Manager setup is almost complete. After all other products are integrated into the network, sync McAfee DLP Manager to the network by completing the final step in this document. McAfee Data Loss Prevention 9.2.0 Installation Guide 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Task
1
On the
Time Configuration
page, change the time zone.
2
Select
Manual
to set NTP to local time.
On this first configuration, you will not yet be able to set the NTP server because the default IP
address (192.168.1.2) will not allow it to be located. The NTP server can be defined only when the
system is restarted and integrated into the network.
3
On the
Policy Activation
page, select the checkboxes of the policies that will generate incidents that
are relevant to your protection strategy.
If you are in a region that is not listed, you will be able to activate policies that are directly relevant
to your location after the system is installed.
4
On the
Administrator Setup
page, enter the email address of the primary administrator and change the
password from the default.
5
On the
Email and Email Server Setting
page, enter the IP address or host name of the email server.
6
On the
Review
page, verify your settings, click
Cancel
, or click
Previous
to change them.
7
When you have confirmed your settings, click
Submit
, then
Exit Wizard
.
At this point, the McAfee DLP Manager setup is almost complete. After all other products are
integrated into the network, sync McAfee DLP Manager to the network by completing the final step
in this document.
Setting up the hardware
Configure McAfee DLP Manager
2
McAfee Data Loss Prevention 9.2.0
Installation Guide
15