Memorex MT2025D Service Manual - Page 5

Replacement Of Memory Ic, Service Adjustment - will not power up

Get Memorex MT2025D - 20inch CRT TV PDF manuals and user guides View all Memorex MT2025D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

3. REPLACEMENT OF MEMORY IC 1. MEMORY IC. This TV uses memory IC. In the memory IC are memorized data for correctly operating the video and deflection circuits. 2. PROCEDURE FOR REPLACING MEMORY IC (1) Power off Switch the power off and unplug the power cord from AC outlet. (2) Replace IC Be sure to use memory IC written with the initial data values. (3) Power On Plug the power cord into the AC outlet and switch the power on. (4) Check and set SYSTEM default value: 1) Press "MENU" "8" "8" "9" "3" buttons in sequence to enter into factory status. 2) If the memory IC haven't been written with the initial data, press [Program+] / [Program-] to select item INIT and press [VOLUME+] / [VOLUME-] to start initialize memory IC. 3) Check the setting value of the SYSTEM default value of Table below. If the value is different, select items by [Program+] / [Program-] keys and set value by [VOLUME+] / [VOLUME-] keys. 4) Press "EXIT" button to return to the normal screen. 4. SERVICE ADJUSTMENT Specific operation: use remote controller Press "MENU" "8" "8" "9" "3" buttons in sequence to enter into factory mode.Press "MENU" to enter into next factory menu. Press [Program+] / [Program-] to select items and press [VOLUME+] / [VOLUME-] key, to make data adjustment of corresponding factory menus. Press "EXIT" key to exit factory mode. Focus adjustment 1. Receive a crosshatch signal. 2. While watching the screen, adjust the FOCUS VR on the FBT to make the vertical and horizontal lines as fine and sharp as possible. Geometrical adjustment Receive NTSC standard complete pattern signal. Adjustment steps： a) Adjust V SC, S emendation b) Adjust V SIZE, to get 92% of vertical picture contents would be displayed on CRT. c) Adjust V POS, the centre horizontal line corresponds to CRT vertical centre. d) Adjust V LIN, to the linearity of P card field is in proper condition. e) Adjust H PHASE, to get the picture horizontal centre correspond to CRT horizontal centre. Receive NTSC signal and repeat above adjustment. 0 PDF pdf Fact or y Pr o www. f i nepr i nt . com. cn

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
0
3. REPLACEMENT OF MEMORY IC
1. MEMORY IC.
This TV uses memory IC. In the memory IC are memorized data for correctly operating the video and deflection
circuits.
2. PROCEDURE FOR REPLACING MEMORY IC
(1) Power off
Switch the power off and unplug the power cord from AC outlet.
(2) Replace IC
Be sure to use memory IC written with the initial data values.
(3) Power On
Plug the power cord into the AC outlet and switch the power on.
(4) Check and set SYSTEM default value:
1) Press
“
MENU
”
±
“
8
”
±
”
8
”
±
”
9
”
±
”
3
”
buttons in sequence to enter into factory status.
2) If the memory IC haven
’
t been written with the initial data, press [Program+] / [Program-] to select
item INIT and press [VOLUME+] / [VOLUME-] to start initialize memory IC.
3)
Check the setting value of the SYSTEM default value of Table below. If the value is different, select
items by [Program+] / [Program-] keys and set value by [VOLUME+] / [VOLUME-] keys.
4) Press
“
EXIT
”
button to return to the normal screen.
4. SERVICE ADJUSTMENT
Specific operation: use remote controller
Press
“
MENU
”
±
“
8
”
±
”
8
”
±
”
9
”
±
”
3
”
buttons in sequence to enter into factory mode.Press
“
MENU
”
to enter into
next factory menu.
Press [Program+] / [Program-] to select items and press [VOLUME+] / [VOLUME-]
key, to make data
adjustment of corresponding factory menus.
Press
“
EXIT
”
key to exit factory mode.
Focus adjustment
1.
Receive a crosshatch signal.
2.
While watching the screen, adjust the FOCUS VR on the FBT to make the vertical and horizontal lines as
fine and sharp as possible.
Geometrical adjustment
Receive NTSC standard complete pattern signal.
Adjustment steps
：
a) Adjust
V SC
,
S emendation
b) Adjust
V SIZE
, to get 92% of vertical picture contents would be displayed on CRT.
c) Adjust
V POS
, the centre horizontal line corresponds to CRT vertical centre.
d) Adjust
V LIN
, to the linearity of P card field is in proper condition.
e) Adjust
H PHASE
, to get the picture horizontal centre correspond to CRT horizontal centre.
Receive NTSC signal and repeat above adjustment.
PDF
文件使用
" pdf Fact or y Pr o"
试用版本创建
www. f i nepri nt . com. cn