Metabo DSD 250 Operating Instructions - Page 15
Accessories
View all Metabo DSD 250 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 15 highlights
ENGLISH ENG Place the side sanding belt cover (16) on the 2 screws (13) and slide (bayonet catch). Tighten the two screws. Adjust the belt run (see chapter 8.6). For sanding belts, see Accessories chapter 10. - Remove adjusting nut (2) with open-ended spanner. Caution! Left-hand thread on left machine side, i.e. to release the adjusting nut (2)on the left machine side, turn clockwise! - Remove clamping flange (3) and grinding wheel (4). - Secure new grinding wheel (4) in the reverse order. - Remount the safety cover (1). Tighten screws. - Adjust the spark deflector (10) and workpiece support (8) as described in chapter 8.2 and 8.1. Replacing the wet grinding wheel (TNS 175 only): - Empty the water container (18): hold a collecting pan under the container and remove the rubber stopper (19). Re-insert the rubber stopper. - Loosen the 3 screws (17) adequately and lower the water container. - Using one hand, hold the grinding wheel (4) secure. Caution! Risk of injury! Wear protective gloves! - Remove adjusting nut with open-ended spanner. (Loosen by turning anti-clockwise). - Remove clamping flange and grinding wheel (4). - Secure new grinding wheel (4) in the reverse order. - Replace the water container (18). (17) Tighten screws. Fill the water container with the correct amount of water (see chapter 8.5) 9.2 Replacing the sanding belt (BS 175 only) Remove the side sanding belt cover (16): release the 2 screws (13), slide the sanding belt cover (16) (bayonet catch) and remove. Swivel out lever (12) as far as it will go. This relieves sanding belt tension and it can now be removed from the rollers. Place the new sanding belt on the rollers so that its direction of circulation (arrows on the inside of the sanding belt) matches the arrow (15) (16)on the side sanding belt cover. Return the lever (12) to the original position to tension the sanding belt. 9.3 Water container (TNS 175 only) Regularly replace the water in the water container (18). To do this, hold a collecting pan under the container and remove the rubber stopper (19). Dismantle the water container for cleaning purposes, as described in chapter 9.1. Use water and a brush (no metal bristles) to clean the inside of the container. a 10 Accessories Use only genuine Metabo accessories. If you need any accessories, check with your dealer. For dealers to select the correct accessory, they need to know the exact model designation of your power tool. A Grinding wheels Order No.: D= 125 mm: 36 P 0900025181 60 N 0900025190 D= 150 mm: 36 P 6.30632 60 N 6.30633 D= 175 mm: 36 P 6.30657 60 N 6.30656 D= 200 mm: 36 P 6.30784 60 N 6.30785 D= 250 mm: 36 P 6.30636 60 N 6.30637 Wet grinding wheel D= 200 mm 0900025653 B Stand Order No 6.23867 C Wall bracket Order no 6.23862 D Sanding belts 3 x P 40 0900025777 3 x P 60 0900025688 3 x P 80 0900025696 3 x P 100 0900025785 3 x P 120 0900025700 3 x P 180 0900025807 3 x P 240 0900025823 3 x P 400 0900025840 For a complete range of accessories, see www.metabo.com or the main catalogue. 15