Motorola HT820 User Manual - Page 1

Start Here > > > HT820 Bluetooth® Stereo Headphones Motorola, Inc. Consumer Advocacy Office 1307 East Algonquin Road Schaumburg, IL 60196 USA www.hellomoto.com 1-877-MOTOBLU 1-800-331-6456 (United States) 1-888-390-6456 (TTY/TDD United States for hearing impaired) 1-800-461-4575 (Canada) 6809496A47-A MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. The Bluetooth trademarks are owned by their proprietor and used by Motorola, Inc. under license. All other product or service names are the property of their respective owners. © Motorola, Inc. 2005. USE THE HT820 Before using this product, read the Important Safety and Legal Information pamphlet and follow its instructions. You can use your HT820 headphones simultaneously with a Bluetooth A2DP enabled audio device and your Bluetooth cell phones! Listen to music, hear a beep, and transfer to take the call on the headphones. Hang up the call with a push of a button and your music automically continues playing. Any Bluetooth HT820 Enabled Audio o Device* 1 CHARGE Your Headphones' Battery Before using your HT820 for the first time, charge the headphones for 2 hours: Charger Insert Charger Here Music Button Indicator Light (Right Side) 1 Plug the Motorola charger into the headphones. The indicator light turns on when the battery is charging. When the headphones' battery is fully charged, the indicator light turns off. Bluetooth Enabled 2 Disconnect the charger. Note: Headphones do not function while charging. Ready to make it work? Phone You can also use a Motorola Original™ - Charge your Headphones for 2 Hours (CHARGE) - Pair headphones & audio device (PAIR) Vehicle Power Adapter to charge your headphones while in your vehicle. - Pair phone & headphones (back side of this guide) A fully charged battery provides - Listen to music and take calls! approximately: 14 hrs of music listening, 17 *The Bluetooth Enabled Audio Device must be A2DP compatible hrs of talk time, or 500 hrs of standby time. 2 PAIR Before you can use your headphones with a Bluetooth enabled product, you must pair it with that product. To pair: 1 Make sure your headphones are turned off (see Turning On and Off ) and press and hold the left side Call m button for 6 seconds until the indicator light turns on and remains steadily lit. Call Button with Indicator Light (Left Side) 2 Next, put your Bluetooth Enabled audio device in pairing mode so the devices can "talk" to each other. For details about putting Bluetooth Enabled devices in pairing mode, refer to the device's User's Guide for directions. Note: To pair the headphones with your phone, see "Pair with your Phone," on the reverse side of this guide. 3 TEST AND USE Your Headphones & Audio Device Your headphones are successfully paired with a device and ready to use when the blue indicator lights changes from steadily lit, flashes rapidly, and then slowly flashes. To confirm they are operating properly: 1 Place the headphones on your head. See Wear the Headphones in this guide. 2 Start playing music on the audio device. If your headphones are successfully paired, you will hear music in the headphones. Note: You may need to wait several seconds before hearing music in the headphones while the devices connect. See Music Controls for information about using the HT820 volume and playback controls. After successfully pairing, you do not need to repeat these initial setup steps each time you use the headphones. Just power on both devices and they automatically connect. TURN ON AND OFF To turn your headphones on, press and hold the left side Call m button until the indicator light flashes 3 times (about 3 seconds). Then, release the button. To turn your headphones off, press and hold the left side Call m button until the indicator light flashes rapidly and then turns off (about 3 seconds). To conserve battery power, turn off the headphones when you will not be using it. WEAR THE HEADPHONES Your headphones are designed to be worn comfortably with the neck band positioned behind your head. The microphone is located in the right ear-piece. Digital Signal processing is used for clear pickup of your voice during voice calls. CONNECT SIMULTANEOUSLY Simultaneous connect your headphones with a music device AND your phone! Pair the headphones to the music device (PAIR). Then pair the headset with your phone (backside of guide). Power your headphones off and then back on. After a few moments it will connect with both the music device and phone. Any Bluetooth Enabled Audio o Device* Bluetooth Enabled Phone Note: The remote control functions only work when the headphones are directly connected to source device. via Bluetooth. MUSIC CONTROLS Left Side Call Button Indicator Volume Buttons Right Side Headphone Jack Skip Reverse Skip Forward Music Button To adjust the volume, press the + or - buttons on the left side of your headphones. To Skip Back to the previous song: Press the Skip Reverse Button < on the right side of your headset. To Skip forward to the next song: Press the Skip Forward Button > To Play, Pause, or Stop music: Press the Music Button M to play, pause, or stop the music. To connect non-Bluetooth Devices to your headphones: Use the headphone jack and the included cable. TROUBLESHOOTING Are you having sound interruption or connection issues? Bluetooth as a wireless technology could be subject to interference of other wireless traffic existing in your environment. Try turning your headphone off and back on. This automatically resets the connection. If you experience audio interruptions while the headphone is connected to both music source and a Bluetooth phone, disconnecting the phone will eliminate the audio interruptions. Support. If you need more help, contact us at 1-877-MOTOBLU or visit us at www.hellomoto.com/bluetooth and click Support.