Motorola RDV2080D User Manual - Page 54

PROGRAMMING, FEATURES, What to do if cloning fails, P/N RLN6303. For details about accessories

Get Motorola RDV2080D - RDX VHF - Radio PDF manuals and user guides
UPC - 723755540019
View all Motorola RDV2080D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

6. Place the Source radio" in its SUC, press and release SB1. 7. After cloning is completed, the Source radio will sound either a "pass" tone (cloning was successful) or a "fail" tone (cloning process has failed). The 'pass' tone sounds like a good key 'chirp' whereas the 'fail' tone sounds similar to a 'bonk' tone. If the Source radio is a display model it will either show 'Pass' or 'Fail' on the display (a tone will be heard in no more than 5 seconds). 8. Once you have completed the cloning process, turn the radios OFFand ON in order to exit 'clone' mode. What to do if cloning fails The radio will emit an audible 'bonk' indicating that the cloning process has failed. In the event that cloning fails, try performing each of the following before trying to start the cloning process again: 1. Ensure that the batteries on both radios are fully charged. 2. Check the cloning cable connection on both SUCs. 3. Ensure that the battery is engaged properly on to the radio. 4. Ensure that there is no debris in the charging tray or on the radio contacts. 5. Ensure that the Source radio is in cloning mode. 6. Ensure that the Target radio is turned ON. 7. Ensure both radios are both from the same type. (same frequency band, same front panel (display/non display), same region and same transmission power). Attention: This cloning cable is designed to operate only with compatible Motorola RLN6170 (Rapid) Single Unit Charger. When ordering Cloning Cable please refer to P/N RLN6303. For details about accessories refer to "Accessories" section. PROGRAMMING FEATURES English 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
52
English
PROGRAMMING
FEATURES
6. Place the Source radio” in its SUC, press
and release SB1.
7. After cloning is completed, the Source radio
will sound either a “pass” tone (cloning was
successful) or a “fail” tone (cloning process has
failed). The ‘pass’ tone sounds like a good key
‘chirp’ whereas the ‘fail’ tone sounds similar to
a ‘bonk’ tone. If the Source radio is a display
model it will either show ‘Pass’ or ‘Fail’ on the
display (a tone will be heard in no more than 5
seconds).
8. Once you have completed the cloning
process, turn the radios OFFand ON in order
to exit ‘clone’ mode.
What to do if cloning fails
The radio will emit an audible ‘bonk’ indicating
that the cloning process has failed. In the event
that cloning fails, try performing each of the
following before trying to start the cloning
process again:
1. Ensure that the batteries on both radios are
fully charged.
2. Check the cloning cable connection on both
SUCs.
3. Ensure that the battery is engaged properly
on to the radio.
4. Ensure that there is no debris in the
charging tray or on the radio contacts.
5. Ensure that the Source radio is in cloning
mode.
6. Ensure that the Target radio is turned ON.
7. Ensure both radios are both from the same
type. (same frequency band, same front panel
(display/non display), same region and same
transmission power).
Attention:
This cloning cable is designed to
operate only with compatible Motorola
RLN6170 (Rapid) Single Unit Charger.
When ordering Cloning Cable please refer to
P/N RLN6303. For details about accessories
refer to “Accessories” section.