NEC 42XR3 User Manual - Page 2

CONFIDENTIAL Specifications For the operation of your plasma monitor, refer to "Operation Manual". Screen Size 918(H)‫ן‬518(V) mm 36.1"(H)‫ן‬20.4"(V) inches diagonal 42" Aspect Ratio 16 : 9 Resolution 1024(H)‫ן‬768(V) pixels Pixel Pitch 0.897(H)‫ן‬0.675(V) mm 0.036"(H)‫ן‬0.027"(V) inches Color Processing 4,096 steps, 68.7 billion colors Signals Synchronization Range Horizontal : 15.5 to 110 kHz (automatic : step scan) Vertical : 50.0 to 120.0 Hz (automatic : step scan) Input Signals RGB, NTSC (3.58/4.43), PAL (B,G,M,N), PAL60, SECAM, HD*1 , DVD*1 , DTV*1 Input Terminals (VIDEO1 and RGB1 can also be used as OUTPUT terminals) RGB Visual 1 (Analog) mini D-sub 15-pin‫ן‬1 Visual 2 (Analog) BNC (R, G, B, H/CS, V)‫ן‬1*2 Visual 3 (Digital) DVI-D 24-pin‫ן‬1*3 Video Visual 1 Visual 2 Visual 3 BNC‫ן‬1 RCA-pin‫ן‬1 S-Video: DIN 4-pin‫ן‬1 DVD/HD/DTV Visual 1 Visual 2 Visual 3 RCA-pin (Y, PB[CB], PR[CR])‫ן‬1*1 BNC (Y, PB[CB], PR[CR])‫ן‬1*1, *2 DVI-D 24-pin‫ן‬1*3 Audio Stereo RCA‫ן‬3(Selectable) External Control D-sub 9-pin‫ן‬1(RS-232C) Sound output 8W+8W at 6 ohm Power Supply AC100-240V 50/60Hz Current Rating 5.2A (maximum) Power Consumption 305W (typical) Dimensions 1018 (W)‫ן‬610 (H)‫ן‬89(D) mm 40 (W)‫ן‬24 (H)‫ן‬3.5 (D) inches Weight 29.5 kg / 65.0 lbs (without stand) Environmental Considerations Operating Temperature 0°C to 40°C / 32°F to 104°F Humidity 20 to 80% (no condensation) Altitude 0 to 2800 m / 0 to 9180 feet Storage Temperature -10°C to 50°C / 14°F to 122°F Humidity 10 to 90% (no condensation) Altitude 0 to 3000 m / 0 to 9840 feet Front Panel User Controls Power on/off, Input source select, Volume up/down, OSM control Remote Control Functions Power on/off, Input source select, OSM control,Volume up/down, Cursor (UP, DOWN,LEFT, RIGHT), Pointer, Zoom up/ down, Off timer, Wireless/ Wired remote control OSM Functions Picture (Contrast/Brightness/Sharpness/Color/Tint/ Picture mode/Noise reduction/Color temperature/ White balance/Gamma/Low tone/Color tune), Audio (Bass/Treble/Balance/Audio input), Image Adjust (Aspect mode/V-Position /H-Position/V-Height /H- Width/Auto Picture/Fine picture/Picture adjustment), Option1 (OSM/BNC Input/D-Sub Input/RGB Select/ HD Select/Input Skip/All Reset), Option2 (Power management/Cinema mode/Long life [PLE, Orbiter, Inverse, White, Screen wiper, Soft focus]/Gray level/ S1/S2/DVI Set up), Option3 (Timer/Power on mode/ Control lock/IR Remote/Loop out/ID number/Video wall [Divider, Position, Disp. mode, Auto ID, Image adjust, Power on delay, PLE link, Timer]), Advanced OSM, Language*, Color system, Source information *English, German, French, Italian, Spanish, Swedish, Chinese, Russian 1018 (40") 918 (36.1") 35 (1.38") 54 (2.13") 518 (20.4") 610 (24") Bezel color is gray. 89 (3.5") Units are in mm (inch) The features and specifications may be subject to change without notice. *1HD/DVD/DTV input signals supported on this system 480P (60 Hz) 480I (60 Hz) 525P (60 Hz) 525I (60 Hz) 576P (50 Hz) 576I (50 Hz) 625P (50 Hz) 625I (50 Hz) 720P (60 Hz) 1035I (60 Hz) 1080I (50 Hz) 1080I (60 Hz) *2The 5-BNC connectors are used as RGB/PC2 and HD/DVD2 input. Select one of them under "BNC INPUT". *3Compatable with HDCP. Supported Signals • 640‫؂‬480P @ 59.94/60Hz • 1920‫؂‬1080I @ 50Hz • 1280‫؂‬720P @ 59.94/60Hz • 720‫؂‬576P @ 50Hz • 1920‫؂‬1080I @ 59.94/60Hz • 1440 (720)‫؂‬576P @ 50Hz • 720‫؂‬480P @ 59.94/60Hz • 1440 (720)‫؂‬480I @ 59.94/60Hz Note: In some cases a signal on the plasma monitor may not be displayed properly. The problem may be an inconsistency with standards from the source equipment (DVD, Set-top box, etc...). If you do experience such a problem please contact your dealer and also the manufacturer of the source equipment. Other Features Accessories Regulations Motion compensated 3D Scan Converter (NTSC, PAL, 480I, 576I, 525I, 625I, 1035I, 1080I), 2-3 pull down Converter (NTSC, 480I, 525I, 1035I, 1080I (60Hz)), 2-2 pull down Converter (PAL, 576I, 625I, NTSC, 480I, 525I), Digital Zoom Function (100-900% Selectable), Video Wall 4-25 multi screen, Self Diagnosis, Image Burn reduction tools (PLE LOCK1~3, INVERSE, WHITE, ORBITER (Auto1,2/Manual), SCREEN WIPER), Color Temperature select (high/mid/mid low/low, user has 4 memories), Control lock (Except power SW), Auto Picture, Input Skip, Color Tune, Low Tone (3 mode), Auto ID, Programmable Timer, Gamma Correction (4 mode), Loop through interface, Plug and play (DDC1, DDC2b, RGB3: DDC2b only) Remote control with two AAA batteries, Power cord, Manuals, Safety metal fittings, Ferrite cores, Bands, Cable clamps Meets EMC Directive (EN55022 Class A, EN55024, EN61000-3-2, EN61000-3-3) Meets Low Voltage Directive (EN60950-1, IEC60950-1, SEMKO Approved) Meets AS/NZS CISPR 22:2002 Class A E-1 4-2