NEC LT380 LT280/LT38 UM - Page 117

Appendix, (1) Troubleshooting, Indicator Messages - status light blinks red

Get NEC LT380 - MultiSync XGA LCD Projector PDF manuals and user guides
UPC - 050927250576
View all NEC LT380 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 117 highlights

8. Appendix ᕡ Troubleshooting This section helps you resolve problems you may encounter while setting up or using the projector. Indicator Messages Power Indicator Blinking light Steady light Indicator Condition Off Green 0.5 sec On, 0.5 sec Off 2.5 sec On, 0.5 sec Off Orange 0.5 sec On, 0.5 sec Off Green Orange Projector Condition Note The main power is off - The projector is getting ready to turn on. Wait for a moment. Off Timer is activated. - The projector is cooling down. Wait for a moment. The projector is turned on. - The projector is in Standby. - Status Indicator Blinking light Indicator Condition Projector Condition Off Normal Red 1 cycle (0.5 sec On, Lamp cover error 2.5 sec Off) 2 cycle (0.5 sec On, Temperature error 0.5 sec Of) 3 cycle (0.5 sec On, Power error 0.5 sec Off) 4 cycle (0.5 sec On, Fan error 0.5 sec Off) 6 cycle (0.5 sec On, Lamp error 0.5 sec Off) Green Re-firing the lamp Orange 1 cycle(0.5 sec On, Network conflict 2.5 sec Off) Steady light Orange Green Control Panel Lock is on The projector is in Standby. Note - Replace the lamp cover correctly. (→ page 105) The projector is overheated. Move the projector to a cooler location. Power unit will not work correctly. Fans will not work correctly. Lamp fails to light. Wait a full minute and then turn on again. The projector is re-firing. Both the built-in LAN and the wireless LAN cannot be connected to the same network at the same time. To use both built-in LAN and wireless LAN at the same time, connect them to different networks. (→ page 87) You have pressed cabinet button when Control Panel Lock is on. (→ page 79) - Lamp Indicator Blinking light Indicator Condition Off Red Steady light Red Green Projector Condition Note Normal - Lamp has reached its end of life. Lamp Replace the lamp. replacement message will be displayed. (→ page 104) Lamp has been used beyond its limit. The Replace the lamp. projector will not turn on until the lamp is (→ page 104) replaced. Lamp is in Eco mode - 107

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
107
8. Appendix
±
Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
Indicator Messages
Power Indicator
Indicator Condition
Projector Condition
Note
Off
Blinking light
Steady light
Green
Orange
Green
Orange
0.5 sec On,
0.5 sec Off
2.5 sec On,
0.5 sec Off
0.5 sec On,
0.5 sec Off
The main power is off
The projector is getting ready to turn on.
Off Timer is activated.
The projector is cooling down.
The projector is turned on.
The projector is in Standby.
–
Wait for a moment.
–
Wait for a moment.
–
–
Status Indicator
Indicator Condition
Projector Condition
Note
Off
Blinking light
Steady light
Red
Green
Orange
Orange
Green
1 cycle (0.5 sec On,
2.5 sec Off)
2 cycle (0.5 sec On,
0.5 sec Of)
3 cycle (0.5 sec On,
0.5 sec Off)
4 cycle (0.5 sec On,
0.5 sec Off)
6 cycle (0.5 sec On,
0.5 sec Off)
1 cycle(0.5 sec On,
2.5 sec Off)
Normal
Lamp cover error
Temperature error
Power error
Fan error
Lamp error
Re-firing the lamp
Network conflict
Control Panel Lock is on
The projector is in Standby.
–
Replace the lamp cover correctly.
(
→
page
105
)
The projector is overheated. Move
the projector to a cooler location.
Power unit will not work correctly.
Fans will not work correctly.
Lamp fails to light. Wait a full
minute and then turn on again.
The projector is re-firing.
Both the built-in LAN and the wireless
LAN cannot be connected to the same
network at the same time.
To use both built-in LAN and wireless
LAN at the same time, connect them to
different networks. (
→
page
87
)
You have pressed cabinet button
when Control Panel Lock is on.
(
→
page
79
)
–
Lamp Indicator
Indicator Condition
Projector Condition
Note
Off
Blinking light
Steady light
Normal
Lamp has reached its end of life. Lamp
replacement message will be displayed.
Lamp has been used beyond its limit. The
projector will not turn on until the lamp is
replaced.
Lamp is in Eco mode
Red
Red
Green
–
Replace the lamp.
(
→
page
104
)
Replace the lamp.
(
→
page
104
)
–