NEC NP-PX803UL-BK Users Manual - Page 24

Rear, make sure you have at least, two people. Attempting to, move the projector alone

Get NEC NP-PX803UL-BK PDF manuals and user guides View all NEC NP-PX803UL-BK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Rear 1. Introduction Controls (→ page 8) Exhaust vent Heated aiir is exhausted from here. (→ page xi, 154) Built-in Security Slot ( )* Terminals (→ page 9) AC IN terminal Connect the supplied power cord's three-pin plug here, and plug the other end into an active wall outlet. (→ page 14) Power Cord Stopper (→ page 16) Main power switch While AC power is being supplied, set the main power switch to ON position (|), then your projector will enter a standby state. * This security slot supports the MicroSaver ® Security System. Security Bar Fixing a theft prevention device. The security bar accepts security wires or chains up to 0.18 inch/4.6 mm in diameter. Handle (located on 4 positions) For transportation NOTE: • For moving the projector, make sure you have at least two people. Attempting to move the projector alone could result in back pain or other injuries. Theft prevention screw hole for the lens unit Intake vent Takes in air to cool the unit. (→ page xi, 154) 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
7
1. Introduction
Rear
AC IN terminal
Connect the supplied
power cord’s three-pin
plug here, and plug the
other end into an active
wall outlet. (
→
page
14
)
Theft prevention screw
hole for the lens unit
Main power switch
While AC power is being supplied, set the
main power switch to ON position (|), then
your projector will enter a standby state.
Power Cord Stopper
(
→
page
16
)
* This security slot supports the MicroSaver
®
Security System.
Built-in Security Slot (
)*
Security Bar
Fixing a theft prevention
device.
The security bar accepts
security wires or chains
up to 0.18 inch/4.6 mm in
diameter.
Handle (located on 4 posi
-
tions)
For transportation
NOTE:
• For moving the projector,
make sure you have at least
two people. Attempting to
move the projector alone
could result in back pain
or other injuries.
Intake vent
Takes in air to cool the unit.
(
→
page
xi
,
154
)
Terminals
(
→
page
9
)
Exhaust vent
Heated aiir is exhausted
from here.
(
→
page
xi
,
154
)
Controls
(
→
page
8
)