Home » Navigon Manuals » Automotive GPS » Navigon 10000130 » Manual Viewer

Navigon 10000130 User Guide - Page 28

Viewing device statuses, GPS, Power, Direction

UPC - 898110001044

Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Basic Operations Viewing device statuses Viewing device statuses Symbols located at the top of the screen are used to display information. GPS The GPS symbol can show the following GPS reception status: No Symbol The built-in GPS receiver is not operational. Contact customer service if the problem persists. No Signal Data is being received from less than three satellites. Position cannot be calculated. GPS Ready Data is being received from at least three satellites. Position can be calculated. For more information, see "About GPS navigation" on page 4. Power The Power symbol can display the following conditions of the built-in battery: The device is powered by an external power source. The battery is charging. The device is powered by its internal battery. Battery is fully charged. The device is powered by its internal battery. Battery charge is sufficient. The device is powered by its internal battery. Battery charge is low. Direction The Direction symbol shows the direction you are currently heading. It can show the following points of the compass: N, NE, E, SE, S, SW, W and NW. 16 NAVIGON 5100 User's Guide January 2008 NAVIGON, INC. Revision 2.0

Section	Page
Table of Contents	7
Introduction	13
About this manual	13
Conventions	13
Symbols	13
Legal notice	13
Liability	13
Trademarks	14
Customer Service	14
Telephone Support	14
E-mail	14
Welcome	15
Introducing Your NAVIGON 5100	15
About GPS navigation	16
Getting Started	17
What’s included	17
Important safety information	18
Navigation safety information	18
Safety information for the navigation device	19
Safety guidelines when installing in your car	19
Preparing your NAVIGON 5100 for use	20
Charging the battery	20
Inserting a memory card	20
Removing the memory card	20
Securing the cradle	21
Securing the navigation device to the cradle	21
Supplying power to the navigation device	21
Connecting the TMC antenna	21
Basic Operations	23
Starting the NAVIGON 5100	23
The Main Window	23
Returning to the Main Window	24
Initializing the GPS receiver	25
Setting the volume	25
Selecting screen orientation	26
Using Standby Mode	27
Stopping the NAVIGON 5100	27
Viewing device statuses	28
GPS	28
Power	28
Direction	28
TMC (Traffic Information)	29
Using software keyboards	30
Alphabetic keyboard	30
Numeric keyboard	30
Special character/symbol keyboard	30
Special keys	31
Using menus	31
Security	33
Password protection	33
The Password Lock Window	33
Setting a password	33
Changing a password	33
Cancelling password protection	34
Forgotten your password?	34
Selecting Destinations	35
Using auto-complete to select a destination	35
Selecting a search area	36
Selecting Destinations	37
Enter an Address	37
Search for POI	37
By Tapping on the Map	37
Entering an address	38
Specifying a city first	38
Specifying a street first	39
Selecting a Point of Interest (POI) destination	40
POIs nearby	40
National POIs	42
POIs in a specified city	44
POI direct access	46
Specify direct access POI categories	47
Information about the POI	48
Selecting a destination by tapping the map	49
Starting navigation	51
Quitting navigation	51
No GPS reception	51
Arriving at your destination	51
Zagat Points of Interest (POIs)	53
Zagat POI Categories	53
Search for Zagat POIs	53
View Zagat POI Information	54
My Destinations	55
Saving a destination	55
Saving the current location using GPS	56
Saving your home address as a destination	56
Selecting a saved destination	57
Selecting a destination from the Last Destinations list	57
Selecting a destination from the Favorites list	58
Navigating homewards	59
Working With Routes	61
Accessing the Route Planning Window	61
Entering the starting point	61
Changing the starting point	62
Entering route points	62
Changing the order of route points	62
Managing routes	63
Saving routes	63
Loading routes	63
Navigation	64
Calculating and displaying routes	64
Viewing the Route Profile	64
Simulating routes	65
Starting a route simulation	65
Ending simulation	65
Viewing a Turn-by-Turn List	66
Blocking route sections	66
Removing blocks and using original routes	66
Working With Maps	67
View information on the current map	68
Selecting a different map	68
View Information About the Map Currently in Use	68
Map in Preview mode	69
Map in Navigation mode	70
Map functions in Navigation mode	71
Map in Destination search mode	72
Operating in Destination search mode	73
Reality View (Junction View)	74
TMC (Traffic Information)	75
Accessing the TMC (Traffic Information) Window	75
The TMC (Traffic Information) Window	76
Types of Messages	76
Traffic Flow Severity Indicators	77
Event or Incident Icons	77
Displaying traffic messages	78
Requesting a route recalculation	79
TMC Settings Window	80
Select another station	80
Select Tuning Mode Settings	80
Select Reroute Settings	81
Specify the type of traffic messages to display	81
Logbook	83
Starting a recording	83
Stopping the recording	83
Customizing Your NAVIGON 5100	85
Accessing the Settings window	85
The Settings window	85
Basic Settings	85
Current Map Settings	87
POI Settings	87
Route Profile Settings	87
Options Button	88
Selecting options	89
Moving between pages	89
Viewing a list of options for a setting	89
Toggling between options	89
Viewing information about a setting	90
Saving changes	90
Discarding changes	90
Legal Notices	91
NOTICE TO DRIVERS IN CALIFORNIA AND MINNESOTA	91
GPS	91
Technical Data	93
Specifications	93
Compliance Notices	94