Netgear 1000 Powerline User Manual - Page 19

Factory Reset, Wait until the Pick A Plug LEDs are lit.

Get Netgear 1000 PDF manuals and user guides View all Netgear 1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

PowerLINE 3. Connect the device to the LAN port on your router or gateway using an Ethernet cable. 4. Plug the second PowerLINE device into a wall outlet where you want to add Internet access. 5. Use the Ethernet cable that came with your adapter to connect the PowerLINE device to an Ethernet port on a computer, game console, Blu-ray player, or other peripheral device. 6. Wait until the Pick A Plug LEDs are lit. 7. To use a private encryption key, press the button on one of the adapters for two seconds, and then press the button on the other adapter for two seconds. Both buttons must be pressed within two minutes. WARNING: Do not press the button on the PowerLINE adapter until installation is complete and the adapters are communicating with each other (indicated by the blinking Power LED). Pressing this button too soon can temporarily disable PowerLINE communication. If this occurs, use the Factory Reset button to return the PowerLINE adapter to its factory default settings. Note: The button does not work in power saving mode. 8. Wait for the PowerLINE network to recognize each PowerLINE device. This process could take as little as 5 seconds or up to 80 seconds. When the Power LEDs stop blinking, the process is complete. If the Pick A Plug LEDs are green or amber, the devices are successfully connected to the PowerLINE network. A red Pick A Plug LED indicates a slow link rate. In this case, move the PowerLINE device to another electrical outlet with a faster connection. 9. If you are installing additional adapters, repeat Step 7 with one of the secure adapters and one of the adapters that is not yet secured. See Use the Button to Set the Encryption Key on page 22. PowerLINE Networks 19 User Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
3.
Connect the device to the LAN port on your router or gateway using an Ethernet
cable.
4.
Plug the second PowerLINE device into a wall outlet where you want to add Internet
access.
5.
Use the Ethernet cable that came with your adapter to connect the PowerLINE device
to an Ethernet port on a computer, game console, Blu-ray player, or other peripheral
device.
6.
Wait until the Pick A Plug LEDs are lit.
7.
To use a private encryption key, press the button on one of the adapters for two
seconds, and then press the button on the other adapter for two seconds.
Both buttons must be pressed within two minutes.
WARNING:
Do not press the button on the PowerLINE adapter until installation is
complete and the adapters are communicating with each other (indicated by the
blinking Power LED). Pressing this button too soon can temporarily disable PowerLINE
communication. If this occurs, use the
Factory Reset
button to return the PowerLINE
adapter to its factory default settings.
Note:
The button does not work in power saving mode.
8.
Wait for the PowerLINE network to recognize each PowerLINE device.
This process could take as little as 5 seconds or up to 80 seconds.
When the Power LEDs stop blinking, the process is complete. If the Pick A Plug LEDs
are green or amber, the devices are successfully connected to the PowerLINE
network. A red Pick A Plug LED indicates a slow link rate. In this case, move the
PowerLINE device to another electrical outlet with a faster connection.
9.
If you are installing additional adapters, repeat Step
7
with one of the secure adapters
and one of the adapters that is not yet secured.
See Use
the
Button
to
Set
the
Encryption
Key
on page 22.
User Manual
19
PowerLINE Networks
PowerLINE