Netgear FS728TS FS752TS Setup Manual - Page 126

QoS > CoS> Advanced > DSCP To Queue Mapping, DSCP to Queue Mapping, DSCP In, Queue

Get Netgear FS728TS - ProSafe Smart Switch PDF manuals and user guides
UPC - 606449043600
View all Netgear FS728TS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 126 highlights

FS700TS Smart Switch Software Administration Manual To map DSCP values to queues: 1. Click QoS > CoS> Advanced > DSCP To Queue Mapping. The DSCP To Queue Mapping screen displays: Figure 5-6 The DSCP To Queue Mapping screen contains the following fields: DSCP to Queue Mapping • DSCP In - Displays the incoming packet's DSCP value. The following DSCP In values are predefined: 3, 11, 19, 27, 35, 43, 51, 59. • Queue - Select the traffic-forwarding queue to which the DSCP is mapped. Four traffic priority queues are supported (Lowest, Low, Normal and High). The High Queue is reserved for special traffic and is not recommended for use. Restore Default Mapping • Restore Defaults- Restore the DSCP Mapping device factory default values. The possible field values are: - Checked - Restore the factory default settings for DSCP mapping values. - Unchecked - Maintain the current DSCP mapping settings. 5-8 Configuring QoS v1.0, September 2007

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
FS700TS Smart Switch Software Administration Manual
5-8
Configuring QoS
v1.0, September 2007
To map DSCP values to queues:
1.
Click
QoS > CoS> Advanced > DSCP To Queue Mapping
. The DSCP To Queue Mapping
screen displays:
The DSCP To Queue Mapping screen contains the following fields:
DSCP to Queue Mapping
•
DSCP In
– Displays the incoming packet’s DSCP value. The following DSCP In values
are predefined: 3, 11, 19, 27, 35, 43, 51, 59.
•
Queue
– Select the traffic-forwarding queue to which the DSCP is mapped. Four traffic
priority queues are supported (Lowest, Low, Normal and High). The High Queue is
reserved for special traffic and is not recommended for use.
Restore Default Mapping
•
Restore Defaults
– Restore the DSCP Mapping device factory default values. The possible
field values are:
–
Checked – Restore the factory default settings for DSCP mapping values.
–
Unchecked – Maintain the current DSCP mapping settings.
Figure 5-6