Home » Netgear Manuals » Hubs & Switches » Netgear GS108Tv2 » Manual Viewer

Netgear GS108Tv2 GS108T/ GS110TP Smart Switch Software Administration Manual - Page 77

Port Speed, Sleep Mode, Short Cable Mode, Physical Status, Link Status, Link Trap, Maximum Frame Size

Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

GS108T and GS110TP Smart Switch Software Administration Manual • Port Speed. Use the menu to select the port's speed and duplex mode. If you select Auto, the duplex mode and speed will be set by the auto-negotiation process. The port's maximum capability (full duplex and 1000 Mbps) will be advertised. Otherwise, your selection will determine the port's duplex mode and transmission rate. The factory default is Auto. • Sleep Mode. Use the menu to select the port's Green Ethernet mode, which can be one of the following: • Enable: Specifies that when the port link is down, the port automatically goes down for a short amount of time and wakes up to check link pulses. When the port does not have a link partner, the sleep mode reduces power consumption. • Disable: The port provides full power to the port even if there is no link partner. • Short Cable Mode. Use the menu to select the port's Green Ethernet mode, which can be one of the following: • Enable: Specifies that cable test is performed when the port link is up at 1 Gbps and if the cable is less than 10m, PHYs are placed in low power mode (nominal power). • Disable: The port does not participate in Green Ethernet mode. • Physical Status. Indicates the physical port's speed and duplex mode • Link Status. Indicates whether the Link is up or down. • Link Trap. This object determines whether or not to send a trap when link status changes. The factory default is Enable. • Enable: Specifies that the system sends a trap when the link status changes. • Disable: Specifies that the system does not send a trap when the link status changes. • Maximum Frame Size. Specify the maximum Ethernet frame size the interface supports or is configured to support. The frame size includes the Ethernet header, CRC, and payload. (1518-9216). The default maximum frame size is 1518. • MAC Address. Displays the physical address of the specified interface. • PortList Bit Offset. Displays the bit offset value which corresponds to the port when the MIB object type PortList is used to manage in SNMP. • ifIndex. The ifIndex of the interface table entry associated with this port. If the interface field is set to All, this field is blank. 6. Click Cancel to cancel the configuration on the screen and reset the data on the screen to the latest value of the switch. 7. If you make any changes to the page, click Apply to apply the changes to the system. 10 | Chapter 3: Configuring Switching Information

Section	Page
GS108T and GS110TP Smart Switch	1
Table of Contents	3
1. Getting Started	8
Getting Started with the GS108T and GS110TP Gigabit Smart Switches	9
Switch Management Interface	10
Connecting the Switch to the Network	11
Switch Discovery in a Network with a DHCP Server	12
Switch Discovery in a Network without a DHCP Server	14
Configuring the Network Settings on the Administrative System	15
Web Access	17
Smart Control Center Utilities	18
Network Utilities	18
Configuration Upload and Download	19
Firmware Upgrade	21
Viewing and Managing Tasks	22
Understanding the User Interfaces	24
Using the Web Interface	24
Using SNMP	29
Interface Naming Convention	30
2. Configuring System Information	32
Management	33
System Information	33
IP Configuration	34
Time	36
Denial of Service	42
DNS	44
Green Ethernet Configuration	47
PoE (GS110TP Only)	48
PoE Configuration	48
PoE Port Configuration	49
Timer Global Configuration	51
Timer Schedule Configuration	52
SNMP	54
SNMPV1/V2	54
Trap Flags	57
SNMP v3 User Configuration	58
LLDP	59
LLDP Configuration	59
LLDP Port Settings	61
LLDP-MED Network Policy	62
LLDP-MED Port Settings	64
Local Information	65
Neighbors Information	67
Services — DHCP Filtering	72
DHCP Filtering Configuration	72
Interface Configuration	73
3. Configuring Switching Information	75
Ports	76
Port Configuration	76
Flow Control	78
Link Aggregation Groups	79
LAG Configuration	79
LAG Membership	81
LACP Configuration	82
LACP Port Configuration	83
VLANs	84
VLAN Configuration	84
VLAN Membership Configuration	86
Port VLAN ID Configuration	87
Voice VLAN	89
Voice VLAN Properties	89
Voice VLAN Port Setting	90
Voice VLAN OUI	91
Auto-VoIP	93
Spanning Tree Protocol	94
STP Switch Configuration	95
CST Configuration	97
CST Port Configuration	98
CST Port Status	100
Rapid STP	101
MST Configuration	102
MST Port Configuration	104
STP Statistics	106
Multicast	108
Auto-Video Configuration	108
IGMP Snooping	109
IGMP Snooping Querier	117
Forwarding Database	121
MAC Address Table	121
Dynamic Address Configuration	123
Static MAC Address	124
4. Configuring Quality of Service	125
Class of Service	126
Basic CoS Configuration	126
CoS Interface Configuration	128
Interface Queue Configuration	129
802.1p to Queue Mapping	130
DSCP to Queue Mapping	131
Differentiated Services	133
Defining DiffServ	133
Diffserv Configuration	134
Class Configuration	135
Policy Configuration	138
Service Configuration	142
Service Statistics	143
5. Managing Device Security	145
Management Security Settings	146
Change Password	146
RADIUS Configuration	147
Configuring TACACS+	153
Authentication List Configuration	155
Configuring Management Access	157
HTTP Configuration	157
Secure HTTP Configuration	158
Certificate Download	159
Access Profile Configuration	161
Access Rule Configuration	162
Port Authentication	164
802.1X Configuration	164
Port Authentication	165
Port Summary	169
Traffic Control	171
MAC Filter Configuration	171
MAC Filter Summary	173
Storm Control	174
Port Security Configuration	175
Port Security Interface Configuration	176
Security MAC Address	178
Protected Ports Membership	179
Configuring Access Control Lists	180
ACL Wizard	180
MAC ACL	182
MAC Rules	183
MAC Binding Configuration	184
MAC Binding Table	186
IP ACL	187
IP Rules	188
IP Extended Rule	189
IP Binding Configuration	193
IP Binding Table	194
6. Monitoring the System	195
Ports	196
Switch Statistics	196
Port Statistics	198
Port Detailed Statistics	199
EAP Statistics	206
System Logs	208
Memory Logs	208
FLASH Log Configuration	210
Server Log Configuration	212
Trap Logs	214
Event Logs	215
Port Mirroring	216
Multiple Port Mirroring	216
7. Maintaining the System	219
Reset	220
Device Reboot	220
Factory Default	221
Upload File From Switch	222
Download File To Switch	223
TFTP File Download	223
HTTP File Download	225
File Management	228
Dual Image Configuration	228
Dual Image Status	229
Troubleshooting	231
Ping	231
Traceroute	232
8. Accessing Help	235
Online Help	235
Support	235
User Guide	236
A. Hardware Specifications and Default Values	238
GS108T and GS110TP Gigabit Smart Switches Specifications	238
GS108 Specifications	238
GS110 Specifications	238
GS108T and GS110TP Switch Performance	239
GS108T and GS110TP Switch Features and Defaults	239
Port Characteristics	239
Traffic Control	240
Quality Of Service	240
Security	240
System Setup	241
Management	241
Other Features	242
B. Configuration Examples	243
Virtual Local Area Networks (VLANs)	244
VLAN Example Configuration	245
Access Control Lists (ACLs)	246
MAC ACL Example Configuration	246
Standard IP ACL Example Configuration	248
Differentiated Services (DiffServ)	249
Class	249
DiffServ Traffic Classes	250
Creating Policies	250
DiffServ Example Configuration	252
802.1X	254
802.1X Example Configuration	255
MSTP	257
MSTP Example Configuration	258
C. Notification of Compliance	262

Match case Limit results 1 per page

Chapter 3:

Configuring Switching Information

GS108T and GS110TP Smart Switch Software Administration Manual

•

Port Speed

. Use the menu to select the port’s speed and duplex mode. If you select

Auto, the duplex mode and speed will be set by the auto-negotiation process. The

port’s maximum capability (full duplex and 1000 Mbps) will be advertised. Otherwise,

your selection will determine the port’s duplex mode and transmission rate. The

factory default is Auto.

•

Sleep Mode

. Use the menu to select the port’s Green Ethernet mode, which can be

one of the following:

•

Enable: Specifies that when the port link is down, the port automatically goes

down for a short amount of time and wakes up to check link pulses. When the port

does not have a link partner, the sleep mode reduces power consumption.

•

Disable: The port provides full power to the port even if there is no link partner.

•

Short Cable Mode

. Use the menu to select the port’s Green Ethernet mode, which

can be one of the following:

•

Enable: Specifies that cable test is performed when the port link is up at 1 Gbps

and if the cable is less than 10m, PHYs are placed in low power mode (nominal

power).

•

Disable: The port does not participate in Green Ethernet mode.

•

Physical Status

. Indicates the physical port’s speed and duplex mode

•

Link Status

. Indicates whether the Link is up or down.

•

Link Trap

. This object determines whether or not to send a trap when link status

changes. The factory default is Enable.

•

Enable: Specifies that the system sends a trap when the link status changes.

•

Disable: Specifies that the system does not send a trap when the link status

changes.

•

Maximum Frame Size

. Specify the maximum Ethernet frame size the interface

supports or is configured to support. The frame size includes the Ethernet header,

CRC, and payload. (1518–9216). The default maximum frame size is 1518.

•

MAC Address

. Displays the physical address of the specified interface.

•

PortList Bit Offset

. Displays the bit offset value which corresponds to the port when

the MIB object type PortList is used to manage in SNMP.

•

ifIndex

. The ifIndex of the interface table entry associated with this port. If the

interface field is set to All, this field is blank.

Click

Cancel

to cancel the configuration on the screen and reset the data on the screen to

the latest value of the switch.

If you make any changes to the page, click

Apply

to apply the changes to the system.