Netgear GSM7248R Configuring IGMP Snooping - Page 3

Set the Management IP address, Enable IGMP Snooping CLI on VLAN 1, Enable IGMP snooping on any VLAN - reset

Get Netgear GSM7248R PDF manuals and user guides View all Netgear GSM7248R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

CONFIGURATION - Management IP address and IGMP Set the Management IP address 1) Plugged the console cable to the Serial port of the switch and the serial port on the PC 2) Open a new Hyper Terminal session (connecting via the COM port) - settings 9600, 8 , None , 1, None 3) Power Cycle the switch 4) Upon POST the User: prompt will appear 5) Username is admin , password "blank" 6) Type Enable to access the privileged mode (password "blank" ) 7) Type network protocol none to reset the network settings 8) Type network parms . For example network parms 192.168.0.2 255.255.255.0 192.168.0.1 9) User copy system:running-config nvram:startup-config to save the configuration 10) Check with show network if the settings are correct The switch should now be accessible patching a CAT5 Straight-through cable. The PC NIC must be configured with an IP address within the same subnet used to configure the management IP of the switch (Example: 192.168.0.2 255.255.255.0 IGMP snooping implementation Enable IGMP Snooping (CLI) on VLAN 1 (GSM7312)# config (GSM7312) (config) #ip igmpsnooping (GSM7312) (config) #ip igmpsnooping unknown-multicast filter (GSM7312) (config) #ip igmpsnooping interfacemode (GSM7312) (config) #exit (GSM7312)# vlan database This command activate IGMP on all the ports in VLAN 1 (GSM7312) (vlan) #ip igmp 1 This command activate the Querier to be the VLAN address (In this case 192.168.0.1) (GSM7312) (vlan) #ip igmpsnooping querier 1 (GSM7312) (vlan) #exit Enable IGMP snooping on any VLAN In order to activate IGMP on any other VLAN the following list of commands must be modified replacing with the VLANID number: GSM7312)# vlan database (GSM7312) (vlan) #ip igmp (GSM7312) (vlan) #ip igmpsnooping querier (GSM7312) (vlan) #exit

  • 1
  • 2
  • 3
  • 4
  • 5
CONFIGURATION – Management IP address and IGMP
Set the Management IP address
1)
Plugged the console cable to the Serial port of the switch and the serial port on the
PC
2)
Open a new Hyper Terminal session (connecting via the COM port) – settings 9600,
8 , None , 1, None
3)
Power Cycle the switch
4)
Upon POST the User: prompt will appear
5) Username is
admin
, password “
blank”
6) Type
Enable
to access the privileged mode (password “
blank”
)
7) Type
network protocol none
to reset the network settings
8) Type
network parms <<Management IP>> <<Subnet Mask>> <<Default Gateway
IP>>
. For example
network parms 192.168.0.2 255.255.255.0 192.168.0.1
9) User
copy system:running-config nvram:startup-config
to save the configuration
10) Check with
show network
if the settings are correct
The switch should now be accessible patching a CAT5 Straight-through cable. The PC
NIC must be configured with an IP address within the same subnet used to configure the
management IP of the switch (Example: 192.168.0.2 255.255.255.0
IGMP snooping implementation
Enable IGMP Snooping (CLI) on VLAN 1
(GSM7312)# config
(GSM7312) (config) #ip igmpsnooping
(GSM7312) (config) #ip igmpsnooping unknown-multicast filter
(GSM7312) (config) #ip igmpsnooping interfacemode
(GSM7312) (config) #exit
(GSM7312)# vlan database
This command activate IGMP on all the ports in VLAN 1
(GSM7312) (vlan) #ip igmp 1
This command activate the Querier to be the VLAN address (In this case 192.168.0.1)
(GSM7312) (vlan) #ip igmpsnooping querier 1
(GSM7312) (vlan) #exit
Enable IGMP snooping on any VLAN
In order to activate IGMP on any other VLAN the following list of commands must be
modified replacing <VLAN-ID> with the VLANID number:
GSM7312)# vlan database
(GSM7312) (vlan) #ip igmp <VLAN-ID>
(GSM7312) (vlan) #ip igmpsnooping querier <VLAN-ID>
(GSM7312) (vlan) #exit