Netgear M4100-26G Installation Guide - Page 2

M4100_IG 7Nov2012.fm Page 2 Friday, November 9, 2012 3:34 PM (switch) #ezconfig EZ Configuration Utility Hello and Welcome! This utility will walk you thru assigning the IP address for the switch management CPU. It will allow you to save the changes at the end. After the session, simply use the newly assigned IP address to access the Web GUI using any public domain Web browser. Admin password is not defined. Do you want to assign the admin password (password length should vary in a range of 8 - 64 characters)? (Y/N/Q) The 'enable' password required for switch configuration via the command line interface is currently not configured. Do you want to assign it (password length should vary in a range of 8 - 64 characters) (Y/N Q)? n Assigning an IP address to your switch management Current IP Address Configuration IP Address Assignment Mode: None IP Address: 0.0.0.0 Subnet mask: 0.0.0.0 Default Router IP: 0.0.0.0 IP address is not assigned. What do you want to do? C - Configure IP address manually. D - Assign IP address for the switch using DHCP mode(current IP address will be lost). N - Do nothing and go to the next question. Q - Quit. ? - Help. (C/D/N/Q/?)? c IP Address: 10.10.10.1 Network mask: 255.255.255.0 Default Router IP: 10.10.10.254 Assigning System Name, System Location and System Contact to your switch management Current Configuration System Name: System Location: System Contact: Do you want to apply and save the changes (Y/N)? y Config file 'startup-config' created successfully . The configuration changes have been applied and saved. Please enter 'show running-config' to see the final configuration. 8. Use the switch IP address returned by ezconfig to log in to the switch (see Log in to the Switch from the Web). For information about how to perform extensive CLI management, see both the CLI reference manual and the software administration guide. September 2012 Computer in DHCP Client Mode with DHCP Server By default, the switch is configured as a DHCP client to obtain its IP address from a DHCP server in the connected network. You need to access the switch from the serial console port. 1. Make sure that the switch is connected to a DHCP server. 2. Find the switch IP address assigned by the DHCP server. a. Perform steps 1 through 3 of the procedure Computer with Static IP Address. b. Type the show network command, and press Enter. A screen displays the active switch IP address. c. Log in to the switch through its web management interface using this IP address (see Log in to the Switch from the Web). Log in to the Switch from the Web Manage your switch through its web interface with the appropriate IP address for your configuration. 1. Type http:// into the URL field of your browser. A screen similar to the following displays. 2. Type admin for the user name, leave the password field blank and click LOGIN. The System Information screen displays. You can now navigate from this point to configure your switch. For the complete EU Declaration of Conformity, visit http://support.netgear.com/app/answers/detail/a_id/11621/. Statement of Conditions: In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit Technical Support After installing your device, locate the serial number on the label of your product and use it to register your product at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support. NETGEAR recommends registering your product through the NETGEAR website. For product updates and web support, visit http://support.netgear.com. NETGEAR recommends that you use only the official NETGEAR support resources. You can get the product manuals online at http://downloadcenter.netgear.com or through a link in the product's user interface. WARNING!! Do not stack equipment, or place equipment in tight spaces, in drawers, or on carpets. Make sure that your equipment has at least 2 inches (5 cm) of air space on all sides. This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union, this product should be treated and recycled in accordance with the laws of your jurisdiction implementing the WEEE Directive. NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice. Other brand and product names are registered trademarks or trademarks of their respective holders. © NETGEAR, Inc. All rights reserved. For indoor use only in all EU countries and Switzerland.