Home » Netgear Manuals » Bridges & Routers » Netgear R6080 » Manual Viewer

Netgear R6080 User Manual - Page 10

Router back panel, Hardware Overview of the Router, AC1000 WiFi Router Model R6080 - wps button

Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

AC1000 WiFi Router Model R6080 Figure 2. Router back panel In addition to the two antennas, the back panel contains the following components: • Reset/WPS button. This button can be used to reboot and reset the router and connect WPS-enabled devices to the router depending on how long the button is pressed: - Reboot the router. Press the button for less than 5 seconds to reboot the router. - Connect WPS-enabled devices. Press the button for about 5 to 10 seconds until the WiFi LED blinks amber. - Reset the router to its factory default settings. Press the button for more than 10 seconds until all the LEDs blink green. • Ethernet LAN ports. Use the four Fast Ethernet RJ-45 LAN ports to connect the router to LAN devices. • Internet WAN port. Use the blue Fast Ethernet RJ-45 WAN port to connect the router to a modem. • Power On/Off button. Press the Power On/Off button to provide power to the router. • DC power connector. Connect the power adapter that came in the product package to the DC power connector. Hardware Overview of the Router 10

Section	Page
Contents	3
1. Hardware Overview of the Router	7
Unpack Your Router	8
LED Descriptions	9
Ports, Buttons, and Connectors on the Back Panel	9
Router Label	11
Position the Router	11
Cable Your Router	12
2. Connect to the Network and Access the Router	13
Connect to the Router	14
Connect to the Router Through an Ethernet Cable	14
Join the WiFi Network of the Router	14
Manual Method	14
Wi-Fi Protected Setup Method	15
Types of Logins	15
Use a Web Browser to Access the Router	16
Automatic Internet Setup	16
Log In to the Router	17
Change the Language	17
Access the Router With the NETGEAR genie App	18
3. Specify Your Internet Settings	19
Use the Internet Setup Wizard	20
Manually Set Up the Internet Connection	20
Specify an Internet Connection Without a Login	20
Specify an Internet Connection That Uses a Login and PPPoE Service	21
Specify an Internet Connection That Uses a Login and PPTP Service	23
Specify an Internet Connection That Uses a Login and L2TP Service	24
Specify an IPv6 Internet Connection	25
IPv6 Internet Connections and IPv6 Addresses	25
Use Auto Detect for an IPv6 Internet Connection	26
Use Auto Config for an IPv6 Internet Connection	27
Set Up an IPv6 6to4 Tunnel Internet Connection	28
Set Up an IPv6 Pass-Through Internet Connection	29
Set Up a Fixed IPv6 Internet Connection	30
Set Up an IPv6 DHCP Internet Connection	31
Set Up an IPv6 PPPoE Internet Connection	32
Manage the MTU Size	34
MTU Concepts	34
Change the MTU Size	35
4. Control Access to the Internet	36
Set Up Parental Controls	37
Allow or Block Access to Your Network	38
Enable and Manage Network Access Control	38
Manage Network Access Control Lists	39
Add Devices to or Remove Them From the Allowed List	40
Add Devices to or Remove Them From the Blocked List	41
Use Keywords to Block Internet Sites	42
Set Up Blocking	42
Remove a Keyword or Domain From the Blocked List	43
Remove All Keywords and Domains From the Blocked List	43
Specify a Trusted Computer	44
Set Up a Schedule for Keyword Blocking and Outbound Firewall Rules	44
5. Manage the Basic WiFi Network Settings	46
Manage the Basic WiFi Settings and WiFi Security of the Main Network	47
View or Change the Basic WiFi Settings and WiFi Security Settings	47
Configure WEP Legacy WiFi Security	52
Configure WPA/WPA2 Enterprise WiFi Security	53
Use WPS to Add a Device to the WiFi Network	55
Use WPS With the Push Button Method	55
Use WPS With the PIN Method	56
Manage the Basic WiFi Settings and WiFi Security of the Guest Network	57
Enable or Disable the WiFi Radios	60
6. Manage the WAN and LAN Network Settings	62
Manage the WAN Security Settings	63
Set Up a Default DMZ Server	63
Manage IGMP Proxying	64
Manage VPN Pass-Through	65
Manage NAT Filtering	65
Manage the SIP Application-Level Gateway	66
Manage the LAN IP Address Settings	66
Manage the Router Information Protocol Settings	67
Manage the DHCP Server Address Pool	68
Manage Reserved LAN IP Addresses	69
Reserve a LAN IP Address	69
Change a Reserved IP Address	70
Remove a Reserved IP Address Entry	70
Disable the Built-In DHCP Server	71
Change the Router’s Device Name	71
Set Up and Manage Custom Static Routes	72
Set Up a Static Route	73
Change a Static Route	74
Remove a Static Route	74
Set Up a Bridge for a Port Group or VLAN Tag Group	75
Set Up a Bridge for a Port Group	75
Set Up a Bridge for a VLAN Tag Group	76
Improve Network Connections With Universal Plug-N-Play	78
7. Manage the Router	79
Update the Firmware of the Router	80
Check for New Firmware and Update the Router	80
Manually Upload New Firmware and Update the Router	81
Change the admin Password	82
Set Up Password Recovery	83
Recover the admin Password	83
Manage the Configuration File of the Router	84
Back Up the Settings	84
Restore the Settings	84
Return the Router to Its Factory Default Settings	85
Use the Reset Button	85
Erase the Settings	86
View the Status and Statistics of the Router	87
View Information About the Router and the Internet and WiFi Settings	87
Display Internet Port Statistics	87
Check the Internet Connection Status	88
Manage the Activity Log	89
View, Email, or Clear the Logs	89
Specify Which Activities Are Logged	90
View Devices Currently on the Network	90
8. Manage the Advanced WiFi Features	92
Set Up a WiFi Schedule	93
Manage the WPS Settings	93
Manage Advanced WiFi Settings	94
Use the Router as a WiFi Access Point Only	95
9. Manage Port Forwarding and Port Triggering	97
Manage Port Forwarding to a Local Server for Services and Applications	98
Forward Incoming Traffic for a Default Service or Application	98
Add a Port Forwarding Rule With a Custom Service or Application	99
Change a Port Forwarding Rule	100
Remove a Port Forwarding Rule	101
Application Example: Make a Local Web Server Public	101
How the Router Implements the Port Forwarding Rule	102
Manage Port Triggering for Services and Applications	102
Add a Port Triggering Rule	103
Change a Port Triggering Rule	104
Remove a Port Triggering Rule	105
Specify the Time-Out for Port Triggering	105
Disable Port Triggering	106
Application Example: Port Triggering for Internet Relay Chat	106
10. Troubleshooting	108
Reboot the Router From Its Web Interface	109
Quick Tips	109
Sequence to Restart Your Network	109
Check Ethernet Cable Connections	109
WiFi Settings	110
Network Settings	110
Troubleshoot With the LEDs	110
Standard LED Behavior When the Router Is Powered On	110
Power LED Is Off or Blinking	110
Power LED Stays Amber	111
Internet or Ethernet LEDs Are Off	111
WiFi LED Is Off	111
You Cannot Log In to the Router	111
You Cannot Access the Internet	112
Check the WAN IP Address	112
Troubleshoot PPPoE	113
Troubleshoot Internet Browsing	114
Changes Are Not Saved	114
Troubleshoot WiFi Connectivity	115
Troubleshoot Your Network Using the Ping Utility	115
Test the LAN Path to Your Router	115
Test the Path From Your Computer to a Remote Device	116
11. Supplemental Information	117
Factory Settings	118