Netgear WG511v2 WG511v2 User Manual - Page 19

Basic Installation Instructions, For Windows XP Users Installing a WG511v2 - 3 2 exe

Get Netgear WG511v2 - 54 Mbps Wireless PC Card 32-bit CardBus PDF manuals and user guides View all Netgear WG511v2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

User Manual for the NETGEAR 54 Mbps Wireless PC Card WG511v2 Your NETGEAR 54 Mbps Wireless PC Card WG511v2 factory default basic settings are: • Network Name Service Set Identification (SSID): Any (First available network) Note: In order for the WG511v2 Wireless PC Card to communicate with a wireless access point or wireless adapter, all devices must be set up to use the same wireless network name (SSID). • Network Mode (Infrastructure or Ad-hoc): Infrastructure • Data security WEP or WPA-PSK encryption: Disabled The section below provides instructions for setting up the NETGEAR 54 Mbps Wireless PC Card WG511v2 for basic wireless connectivity to an access point. The procedures below provide stepby-step installation instructions for Windows PCs. Use the procedure that corresponds to the version of Windows that you are using. Basic Installation Instructions Use the procedure below that corresponds to the version of Windows you are using. For Windows XP Users Installing a WG511v2 1. First, install the WG511v2 software. a. Insert the NETGEAR CD. If the CD main page does not appear, double click autorun.exe on the CD. b. Click the Install Software link and the Smart Wizard starts. c. Follow the Wizard steps, and click Next to continue. d. When the Installation Complete message appears, click Next. Figure 3-1 Basic Setup 3-3 v2.2, December 2005

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
User Manual for the NETGEAR 54 Mbps Wireless PC Card WG511v2
Basic Setup
3-3
v2.2, December 2005
Your NETGEAR 54 Mbps Wireless PC Card WG511v2 factory default basic settings are:
•
Network Name Service Set Identification (SSID):
Any
(First available network)
•
Network Mode (Infrastructure or Ad-hoc):
Infrastructure
•
Data security WEP or WPA-PSK encryption:
Disabled
The section below provides instructions for setting up the NETGEAR 54 Mbps Wireless PC Card
WG511v2 for basic wireless connectivity to an access point. The procedures below provide step-
by-step installation instructions for Windows PCs. Use the procedure that corresponds to the
version of Windows that you are using.
Basic Installation Instructions
Use the procedure below that corresponds to the version of Windows you are using.
For Windows XP Users Installing a WG511v2
1.
First, install the WG511v2 software.
Note:
In order for the WG511v2 Wireless PC Card to communicate with a wireless
access point or wireless adapter, all devices must be set up to use the same
wireless network name (SSID).
a.
Insert the NETGEAR CD.
If the CD
main page does not appear, double click
autorun.exe
on the CD.
b.
Click the
Install Software
link and the
Smart Wizard starts.
c.
Follow the Wizard steps, and click
Next
to continue.
d.
When the Installation Complete
message appears, click
Next
.
Figure 3-1