Netgear WG511v2 WG511v2 User Manual - Page 50

Did the WG511v2 card receive a valid IP address from the Wireless Router/AP?

Get Netgear WG511v2 - 54 Mbps Wireless PC Card 32-bit CardBus PDF manuals and user guides View all Netgear WG511v2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

User Manual for the NETGEAR 54 Mbps Wireless PC Card WG511v2 The WG511v2 Smart Wizard keeps asking me to save my settings This is because you have made changes to the settings and the Smart Wizard is offering you the chance to save the changes. If you want to avoid these Profile setting prompts, simply click Apply before you close the Smart Wizard. Ad Hoc mode is not working correctly You need to click the Initiate Ad Hoc button before you click Apply. Here is how you start an Ad Hoc network: 1. Fill in the Network Name (SSID). 2. Select the Computer-to-Computer (Ad Hoc) Network Type. 3. Click Initiate Ad Hoc. 4. Accept the default settings or make your changes and click OK 5. Click Apply. Note: Be sure all computers in your Ad Hoc network are configured with static IP addresses in the same subnet. How to use the wireless configuration utility that comes with Windows XP During the WG511v2 software installation the wizard prompts you to choose either the NETGEAR Smart Wizard or the Windows configuration utility. Be sure the WG511v2 is in the CardBus slot in the laptop computer and follow these instructions to change your selection. 1. Go to Control Panel and select Network Connections. 2. Right click on the connection and select Properties. 3. Click the Wireless Networks tab. 4. Select or clear the WG511v2 "Use Windows to configure my wireless network settings" check box. Did the WG511v2 card receive a valid IP address from the Wireless Router/AP? The easiest way is to click the system tray icon to open the WG511v2 Smart Wizard. Then check the IP address in the About page. 5-2 Troubleshooting vv2.2, December 2005

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
User Manual for the NETGEAR 54 Mbps Wireless PC Card WG511v2
5-2
Troubleshooting
vv2.2, December 2005
The WG511v2 Smart Wizard keeps asking me to save my settings
This is because you have made changes to the settings and the Smart Wizard is offering you the
chance to save the changes. If you want to avoid these Profile setting prompts, simply click
Apply
before you close the Smart Wizard.
Ad Hoc mode is not working correctly
You need to click the Initiate Ad Hoc button before you click
Apply
. Here is how you start an Ad
Hoc network:
1.
Fill in the Network Name (SSID).
2.
Select the Computer-to-Computer (Ad Hoc) Network Type.
3.
Click Initiate Ad Hoc.
4.
Accept the default settings or make your changes and click OK
5.
Click
Apply
.
How to use the wireless configuration utility that comes with Windows XP
During the WG511v2 software installation the wizard prompts you to choose either the
NETGEAR Smart Wizard or the Windows configuration utility. Be sure the WG511v2 is in the
CardBus slot in the laptop computer and follow these instructions to change your selection.
1.
Go to Control Panel and select Network Connections.
2.
Right click on the connection and select Properties.
3.
Click the Wireless Networks tab.
4.
Select or clear the WG511v2 “Use Windows to configure my wireless network settings” check
box.
Did the WG511v2 card receive a valid IP address from the Wireless Router/AP?
The easiest way is to click the system tray icon to open the WG511v2 Smart Wizard. Then check
the IP address in the About page.
Note:
Be sure all computers in your Ad Hoc network are configured with static IP
addresses in the same subnet.