Netgear WNDRMACv2 WNDRMAC User Manual - Page 98

Troubleshooting with the LEDs, Power LED Is Off or Blinking, LEDs Never Turn Off - wndrmac firmware

Get Netgear WNDRMACv2 PDF manuals and user guides View all Netgear WNDRMACv2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

N600 Wireless Dual Band Gigabit Router WNDRMAC • Wired and wirelessly connected computers need to have network (IP) addresses on the same network as the router. The simplest way to do this is to configure each computer to obtain an IP address automatically using DHCP. • Some cable modem service providers require you to use the MAC address of the computer initially registered on the account. You can view the MAC address in the Attached Devices screen. Troubleshooting with the LEDs After you turn on power to the router, the following sequence of events should occur: 1. When power is first applied, verify that the Power LED is on. 2. After approximately 2 minutes, verify that: • The Power LED is solid green. • The Internet LED is on. • The Ethernet LAN LED is on if any local port is connected to a computer. This indicates that a link has been established to the connected device. The LEDs on the front panel of the router can be used for troubleshooting. Power LED Is Off or Blinking • Make sure that the power cord is securely connected to your router and that the power adapter is securely connected to a functioning power outlet. • Check that you are using the 12V DC, 2.5A power adapter that NETGEAR supplied for this product. • If the Power LED blinks green every second, the router software is corrupted. This can happen if a firmware upgrade is interrupted, or if the router detects a problem with the firmware. If the error persists, you have a hardware problem. For recovery instructions, or help with a hardware problem, contact Technical Support at www.netgear.com/support. LEDs Never Turn Off When the router is turned on, the LEDs turn on for about 10 seconds and then turn off. If all the LEDs stay on, there is a fault within the router. If all LEDs are still on 1 minute after power-up: • Cycle the power to see if the router recovers. • Clear the router's configuration to factory defaults, as explained in Factory Default Settings on page 104. If the error persists, you might have a hardware problem and should contact Technical Support at www.netgear.com/support. Troubleshooting 98

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Troubleshooting
98
N600 Wireless Dual Band Gigabit Router WNDRMAC
•
Wired and wirelessly connected computers need to have network (IP) addresses on the
same network as the router. The simplest way to do this is to configure each computer to
obtain an IP address automatically using DHCP.
•
Some cable modem service providers require you to use the MAC address of the
computer initially registered on the account. You can view the MAC address in the
Attached Devices screen.
Troubleshooting with the LEDs
After you turn on power to the router, the following sequence of events should occur:
1.
When power is first applied, verify that the Power LED
is on.
2.
After approximately 2 minutes, verify that:
•
The Power LED is solid green.
•
The Internet LED is on.
•
The Ethernet LAN LED is on if any local port is connected to a computer. This
indicates that a link has been established to the connected device.
The LEDs on the front panel of the router can be used for troubleshooting.
Power LED Is Off or Blinking
•
Make sure that the power cord is securely connected to your router and that the power
adapter is securely connected to a functioning power outlet.
•
Check that you are using the 12V DC, 2.5A power adapter that NETGEAR supplied for
this product.
•
If the Power LED blinks green every second, the router software is corrupted. This can
happen if a firmware upgrade is interrupted, or if the router detects a problem with the
firmware. If the error persists, you have a hardware problem. For recovery instructions, or
help with a hardware problem, contact Technical Support at
www.netgear.com/support.
LEDs Never Turn Off
When the router is turned on, the LEDs turn on for about 10 seconds and then turn off. If all
the LEDs stay on, there is a fault within the router.
If all LEDs are still on 1 minute after power-up:
•
Cycle the power to see if the router recovers.
•
Clear the router’s configuration to factory defaults, as explained in
Factory Default
Settings
on page 104.
If the error persists, you might have a hardware problem and should contact Technical
Support at
www.netgear.com/support
.