Netgear WNR3500v1 WNR3500 User Manual - Page 70

Wireless Repeating Function, Get Dynamically From ISP Gateway

Get Netgear WNR3500v1 - RangeMax Wireless N Gigabit Router PDF manuals and user guides View all Netgear WNR3500v1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

NETGEAR RangeMax™ Wireless-N Gigabit Router WNR3500 User Manual In the scenario shown, the following conditions must be met for both APs: • Both APs must use the same SSID, wireless channel, authentication mode (if any), and encryption mode (see information about WEP in "Configuring WEP Wireless Security" on page 2-9"). • Both APs must be on the same LAN IP subnet. That is, all the AP LAN IP addresses are in the same network. • All LAN devices (wired and wireless computers) must be configured to operate in the same LAN network address range as the APs. • If you are using DHCP, the Get Dynamically From ISP Gateway radio button in the Internet IP Address section of the Basic Settings screen should be selected for all AP devices in the IP Address Source section. Wireless Repeating Function You can view or change wireless repeater settings for the wireless router. From the main menu of the browser interface, under Advanced, click Wireless Repeating Function to display the Wireless Repeating Function screen. Figure 4-7 4-12 v1.0, March 2008 Customizing Your Network Settings

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
NETGEAR RangeMax™ Wireless-N Gigabit Router WNR3500 User Manual
4-12
Customizing Your Network Settings
v1.0, March 2008
In the scenario shown, the following conditions must be met for both APs:
•
Both APs must use the same SSID, wireless channel, authentication mode (if any), and
encryption mode (see information about WEP in
“Configuring WEP Wireless Security” on
page 2-9”
).
•
Both APs must be on the same LAN IP subnet. That is, all the AP LAN IP addresses are in the
same network.
•
All LAN devices (wired and wireless computers) must be configured to operate in the same
LAN network address range as the APs.
•
If you are using DHCP, the
Get Dynamically From ISP Gateway
radio button in the Internet
IP Address section of the Basic Settings screen should be selected for all AP devices in the IP
Address Source section.
Wireless Repeating Function
You can view or change wireless repeater settings for the wireless router. From the main menu of
the browser interface, under Advanced, click
Wireless Repeating Function
to display the
Wireless Repeating Function screen.
Figure 4-7