Netgear XSM7224S XSM7224S Installation Guide - Page 1

XSM7224S_IG 10Nov10.fm Page 1 Wednesday, November 10, 2010 9:52 AM Installation Guide 24 Port 10G SFP+ Managed Switch XSM7224S Start Here Before you begin installation of your switch, check the Package Contents listed in the Hardware Installation Guide that supports your switch on your Resource CD. If any item is missing or damaged, contact your place of purchase. Other documentation available on your Resource CD for your switch are the Software Administration Guide, and a Command Line Interface Reference Manual. Follow these quick steps to install your switch. You can also consult the full Hardware Installation Guide for your switch on the Resource CD. Set Up the Switch Prepare the site so that the mounting, access, power source, and environmental requirements are met. If you have any questions about these requirements, see the Hardware Installation Guide for your switch on your Resource CD. 1. Install the switch using one of the following methods: a. On a flat surface: Put one of the rubber footpads that came with the switch on each of the four concave spaces on the bottom of the switch. b. In a Rack: Use the rack-mount kit supplied with your switch, following the installation instructions included with the kit,. 2. Apply AC power. When you apply power, the power LED can display the following behavior: • The power LED will blink yellow as it conducts a Power-On Self Test (POST). After the switch passes the POST, the LED turns green. The switch is now functional. If the POST fails, the Power LED will remain yellow (see "Troubleshooting" in the Hardware Installation Manual for assistance). • If the power LED does not light, check that the power cable is plugged in correctly and that the power source is good. If this does not resolve the problem, see "Troubleshooting" in the Hardware Installation Guide on the Resource CD. 3. Connect devices to the switch. • Use Category 6A(Cat6a) for copper ports at 10Gbps • Use Category 5e (Cat5e) for copper ports at 1000Mbps • Use NETGEAR AGM731F or AGM732F for fiber ports at 1000Mbps. • Use NETGEAR AXM761, AXM762, or AXM763 for fiber ports at 10Gpbs. Note: In the room housing the switch, ensure that the ambient temperature does not exceed the specified operating temperature and that the environment is free of water condensation. Perform the Initial Configuration This switch can be managed through its Web interface, or by using the Command Line Interface (CLI) through the serial console port. This guide describes the Web method. The CLI method is also described to determine a DHCP-assigned IP address or to use ezconfig to assign a static IP address. For Web management, follow one of the following three procedures, depending upon how your PC is set up. • PC in DHCP client mode without DHCP server • PC with static IP address • PC in DHCP client mode with DHCP server To perform extensive CLI management, see both the CLI Reference Manual for your switch and the 7000 Series Administration Guide. PC in DHCP Client Mode without DHCP Server WARNING!! If no DHCP server is present, the switch assumes a default IP address of 169.254.100.100 and a subnet mask of 255.255.0.0. The switch is in the same subnet used by a PC NIC port when in DHCPclient mode without a DHCP server present. Use this IP value to log into the switch (see "Web Login to the Switch"). PC with Static IP Address When the PC is in this mode, the switch must also be assigned a static IP address. To assign a static IP Address, access the switch from the serial console port as follows: 1. Connect a console to the switch. Using the null-modem cable supplied with the switch, connect a VT100/ANSI terminal or a workstation to the switch port labeled Console. 2. Start a terminal emulation program (TEP). a. Start a TEP using the appropriate method for your operating system: • Windows users can use HyperTerminal. • Windows Vista users should download a TEP from the Internet. • Macintosh users can use ZTerm. • UNIX users can use a terminal emulator such as TIP. b. Configure the TEP to use the following settings (they are written below the connector on the switch front panel): • Baud rate: 9,600 bps • Data bits: 8 • Parity: none • Stop bit: 1 • Flow control: none c. At the command prompt User:, login to the switch using the user name admin, then press Enter. At the password prompt, press Enter again (no password is needed for initial configuration). d. At the next command prompt, type ezconfig and press Enter. The ezconfig utility is now running in the switch. Use it to set up your static IP address and subnet mask as shown in the following example. Make sure that the selected switch IP address is in the same subnet as that of the PCs.