NordicTrack Elite 3200 Treadmill English Manual - Page 9

Damaged When The Power Is Turned On.

Page 9 highlights

5. Pivot the piston end of the Gas Spring (88) downward. 5 Remove the Spring Pin (102) from the end of the Gas Spring. Next, hold the end of the Gas Spring (88) near the indicated bracket on the Base (83). Press the end of the Gas Spring as far as possible onto the ball on the bracket. If necessary, pivot the Frame (48) slightly and rotate the Gas Spring to align the end of the Gas Spring with the ball on the bracket. See the inset drawing. Insert the Spring Pin (102) into two of the small holes in the end of the Gas Spring, and rotate the Spring Pin until it clips onto the Gas Spring. 83 102 48 88 Bracket 88 With the help of a second person, lower the Frame (48) back to the floor. 102 Bracket 6. Remove the elastic bands securing the Upright Wire Harness (75) and the TV Cable (110). Next, insert the Upright Wire Harness and the TV Cable through the Handrail Spacers (95) as shown, and press the Handrail Spacers into the tops of the Uprights (73, 74). Have two persons hold the console assembly near the Uprights (73, 74). Connect the Upright Wire Harness (75) to the wire harness on the console assembly. See the inset drawing. The connectors should slide together easily and snap into place. If they do not, turn one connector and try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Next, connect the TV Cable (110) to the cable on the left side of the console assembly. Insert the Upright Wire Harness (75) and the TV Cable (110) down into the Uprights (73, 74). Next, insert the brackets on the console assembly into the Uprights. Be careful not to pinch the wires. 6 Cable 110 Console 95 Assembly 73 95 Console Wire 75 74 75 7. Finger tighten three Handrail Bolts (64), with three Handrail Star Washers (90), into the Right Upright (74) and the console assembly. Repeat this step with the Left Upright (73). After all six Handrail Bolts have been started, tighten the four front Handrail Bolts first, and then tighten the other two Handrail Bolts. 7 Console Assembly 73 64 90 64 90 74 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38

9
5.
Pivot the piston end of the Gas Spring (88) downward.
Remove the Spring Pin (102) from the end of the Gas
Spring.
Next, hold the end of the Gas Spring (88) near the indi-
cated bracket on the Base (83). Press the end of the Gas
Spring as far as possible onto the ball on the bracket. If
necessary, pivot the Frame (48) slightly and rotate the
Gas Spring to align the end of the Gas Spring with the
ball on the bracket. See the inset drawing. Insert the
Spring Pin (102) into two of the small holes in the end of
the Gas Spring, and rotate the Spring Pin until it clips
onto the Gas Spring.
With the help of a second person, lower the Frame (48)
back to the floor.
88
102
5
83
48
Bracket
6.
Remove the elastic bands securing the Upright Wire
Harness (75) and the TV Cable (110). Next, insert the
Upright Wire Harness and the TV Cable through the
Handrail Spacers (95) as shown, and press the Handrail
Spacers into the tops of the Uprights (73, 74).
Have two persons hold the console assembly near the
Uprights (73, 74). Connect the Upright Wire Harness (75)
to the wire harness on the console assembly.
See the
inset drawing. The connectors should slide together
easily and snap into place.
If they do not, turn one con-
nector and try again.
IF THE CONNECTORS ARE NOT
CONNECTED PROPERLY, THE CONSOLE MAY BE
DAMAGED WHEN THE POWER IS TURNED ON.
Next, connect the TV Cable (110) to the cable on the left
side of the console assembly.
Insert the Upright Wire Harness (75) and the TV Cable
(110) down into the Uprights (73, 74). Next, insert the
brackets on the console assembly into the Uprights.
Be
careful not to pinch the wires.
Console
Assembly
Cable
73
Console
Wire
95
75
74
6
95
110
7.
Finger tighten three Handrail Bolts (64), with three
Handrail Star Washers (90), into the Right Upright (74)
and the console assembly. Repeat this step with the Left
Upright (73).
After all six Handrail Bolts have been
started, tighten the four front Handrail Bolts first,
and then tighten the other two Handrail Bolts.
7
Console
Assembly
90
64
90
73
74
64
75
102
88
Bracket