Oki B6100 Booklet: B6100 Warranty, Regulatory, and Safety Information - Page 3

Customer Support Professionals: Latin America Our customer support professionals are trained and certified on all current OKI products. Make sure that you are close to your printer when you call one of our OKI authorized service centers so that you can describe your problem more accurately. Customer support professionals can answer your questions regarding: • Location of nearest Authorized Service Center • Installation of your machine • Usage/normal maintenance of your machine • Error message interpretation/solutions • Parts and supplies identification • Consumer relations Material Safety Data Sheet MSDS#58358601 Product Identification and Use B6100 Black Toner, P/N 52113701 For more information, contact Oki Data at 2000 Bishops Gate Blvd., Mount Laurel, NJ, 08054-4620. Emergency Information: Call 1-800-654-3282; US & Canada Only Hazardous Ingredients Styrene/acrylate copolymer (55-60% by weight) CAS#: Not available Iron oxide (35-40% by weight) CAS#: Not available Polypropylene (less than 3% by weight) CAS#: Not available Amorphous silica (less than 1% by weight) CAS#: Not available Chromium/azo dye complex (less than 1% by weight) CAS#: 84179-66-8, 10-125-50-0, 109125-51-1 Physical Data Physical State: Solid Melting/Freezing Point: Not available Boiling Point: Not applicable PH: Not available. Vapor Pressure: Not applicable Vapor Density (Air=1): Not available Evaporation Rate (Butyl Acetate=1): Not available Specific Gravity (H2O=1): Not available Solubility in water: Negligible Solubility in solvents: Not available Coefficient of water/oil Distribution: Not available Appearance and odor: Black powder, faint odor Odor Threshold: Not available Fire and Explosion Hazard Data Flammability: Not flammable under conditions of use. Extinguishing Media: In case of fire, use extinguishing media (water spray, foam, dry chemicals). When in a machine, treat as an electrical fire. Flash Point (OC): Not applicable Lower Explosive Limit: Not applicable Upper Explosive Limit: Not applicable Auto-ignition Temperature: Not applicable Hazardous Combustion Products: Not applicable Explosion Data Like most organic materials in powder form, it can form explosive mixtures when dispersed in air. Sensitivity to Mechanical Impact: Not available Sensitivity to Static Discharge: Not available Reactivity Data Stability: Stable Conditions to Avoid: Not available Polymerization: Not available Hazardous Decomposition Products: Not available Incompatibility: Not available Toxicological Properties Routes of Entry: Inhalation, Ingestion, Eyes, Skin Effects of Acute Exposure: Practically non-toxic Swallowed LD50 (rat): >5.0 g/kg1) Skin LD50 (rabbit): >2.0 g/kg1) Inhaled LC50 (rat): >5.0 mg/L/4hr1) Effects of Chronic Exposure: The results obtained from a sponsored, Chronic Toner Inhalation Study, demonstrated no lung change in rats for the lowest (1 mg/ m3) exposure level (i.e. the level most relevant to potential human exposure). A very slight degree of fibrosis was noted in 25% of the animals at the middle (4 mg/m3) exposure level, while a slight degree of fibrosis was noted in all the animals at the highest (16 mg/m3) exposure level. These findings are attributed to "lung overloading", a generic response to excessive amounts of any dust retained in the lungs for a prolonged period. This study was conducted using a special test toner to comply with EPA testing protocol. The test toner was ten times more respirable than commercially available OKI toner, and would not be functionally suitable for OKI equipment.1) Exposure Limits: ACGIH TLV (2002): 10 mg/m3 (Total) 3 mg/m3 (Respirable) Irritancy: Not an irritant1) English 3