Oki ML490 Guide: User's ML490/491 (English) - Page 14

Setting Top of Form TOF

Get Oki ML490 PDF manuals and user guides View all Oki ML490 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Setting Top of Form (TOF): Forms Tear-Off OFF (Default Setting) Important! If you turn the platen knob when the printer is on, the Top of Form misaligns. Always turn the printer off before turning the platen knob! Note: The first line prints at the red line (1) of the plastic paper shield on the printhead. With paper loaded and the printer on and selected: 1 Press SEL | MENU (1) to take the printer off line. The SEL light goes out. 2 Press and hold SHIFT (2), then Note: When you begin pressing the Micro Feed key, the printhead will move to the right. • Press LF | Micro Feed Down (3) to set the TOF higher (the paper moves down). • Press FF/LOAD | Micro Feed Up (4) to set the TOF lower (the paper moves up). 3 When you have the TOF set where you want it, press and hold SHIFT (2), then press QUIET/TOF (7) to engage the new setting. The printhead moves back to the left margin. 4 Press SEL/MENU (1) to save the setting and place the printer back on line. Note: To reset the Top of Form to the factory default, see "Resetting Top of Form to the Factory Default" later in this chapter. 14 Microline 490/491 User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
14
Microline 490/491 User’s Guide
Setting Top of Form (TOF):
Forms Tear-Off OFF (Default Setting)
Important!
If you turn the platen knob when the printer is on, the Top of
Form misaligns. Always turn the printer off before turning
the platen knob!
Note:
The first line prints at the red line (1) of the plastic
paper shield on the printhead.
With paper loaded and the printer on and selected:
1
Press
SEL | MENU
(1) to take the printer off line.
The SEL light goes out.
2
Press and hold
SHIFT
(2), then
Note:
When you begin pressing the Micro Feed key, the
printhead will move to the right.
• Press
LF | Micro Feed Down
(3) to set the TOF
higher
(the
paper moves down).
• Press
FF/LOAD | Micro Feed Up
(4) to set the TOF
lower
(the paper moves up).
3
When you have the TOF set where you want it, press and
hold
SHIFT
(2), then press
QUIET/TOF
(7) to engage the new
setting.
The printhead moves back to the left margin.
4
Press
SEL/MENU
(1) to save the setting and place the printer
back on line.
Note:
To reset the Top of Form to the factory default, see
“Resetting Top of Form to the Factory Default” later in
this chapter.