Onkyo DV-SP800 Instruction Manual - Page 12

Index to Parts and Controls I Rear panel 1 23 4 VIDEO OUTPUT COMPONENT Y PB PR S VIDEO VIDEO CH 1 L ANALOG OUTPUT R CH 2 FRONT SURR 1 CENTER SURR 2 SUB WOOFER L SURR 1 1+2 R DIGITAL OUTPUT OPTICAL COAXIAL REMOTE CONTROL SACD & DVD AUDIO/VIDEO PLAYER MODEL NO. DV-SP800 AC INLET 5 6 78 9 0 - European models. = ~ S VIDEO PR VIDEO IN/ OUT AV CONNECTOR 1 RONT SURR 1 CENTER SURR 2 SUB WOOFER L SURR 1 1+2 R DIGITAL OUTPUT OPTICAL COAXIAL AV CONNECTOR 2 OUT REMOTE CONTROL SACD & DVD AUDIO/VIDEO PLAY MODEL NO. DV-SP800 Shapes of jacks vary depending on the area in which it was purchased. 1 VIDEO OUTPUT COMPONENT jacks [16] If your TV has component inputs, you can connect a component video cable to your TV and to your DVD Player for ideal video quality. The component Video Cable only carries the video signal; remember to connect the left and right audio cables. If you connect a TV that is compatible with a Progressive scan signal, you can enjoy both Interlaced and Progressive scan. 2 VIDEO OUTPUT S VIDEO jack [16, 17] If your TV or monitor has an S-video input, clear picture reproduction is possible by connecting the player to your TV or monitor via the S-Video jack. You can switch between [S1] and [S2] S-video output from the Setup menu. 3 VIDEO OUTPUT VIDEO jack [15] Connect to the video input on a TV or monitor or AV amplifier or receiver with video input capability. 4 AC INLET [20] Use to connect the power cord to the wall outlet. 5 ANALOG OUTPUT CH 1/CH 2 jacks [16-19] Use to output two-channel audio (analog) to the audio stereo inputs on a TV or stereo amplifier. 6 ANALOG OUTPUT FRONT/SURR 1/CENTER/ SUBWOOFER jacks [19] Use to output 5.1 channel audio (analog) to the 5.1 channel discrete inputs on an amplifier. If you are connecting to a receiver that has both digital and analog input jacks for DVD player connection, it may be beneficial to make both connections. 7 SURR 2 jacks [19] Use when making connections to 7.1 channel analog inputs. (Make sure the SURR 1/1+2 selector switch is set to 1+2.) 8 SURR 1/1+2 selector switch [19] When using 2 channel surround, select 1, when using 4 channel surround, select 1+2. Audio will be output 3dB lower when 1+2 is selected. The same audio is output from SURR 1 and from SURR 2. 9 DIGITAL OUTPUT OPTICAL jack [18] Use to output the digital audio signal recorded on discs. You can output the digital signal via the optical output jack to an AV amplifier or receiver. 0 DIGITAL OUTPUT COAXIAL jack [18] Use to output the digital audio signal recorded on discs. You can output the digital signal via the coaxial output jack to an AV amplifier or receiver. - z jack [18, 19] Use to connect this player to another component bearing the z mark. This lets you control this unit as though it were a component in a system. (The components will not function as a system with only z connections. Be sure to connect the audio connection cables correctly as well). (European models) = AV CONNECTOR 1 (IN/OUT) jack [17] Use a 21-pin SCART cable to connect to a TV, monitor or video component compatible with this type of connection. Outputs both audio and video (composite only) when the unit is powered on. When the unit is in standby mode, this jack becomes an input for audio and video (RGB, S, and composite). ~ AV CONNECTOR 2 (OUT) jack [17] Use a 21-pin SCART cable to connect to a TV or monitor compatible with this type of connection. Outputs audio and video (RGB, S, and composite) when the unit is powered on. When the unit is in standby mode, this jack outputs the audio and video input from the AV CONNECTOR 1 jack. 12