Onkyo HT-R510 Owner Manual
Onkyo HT-R510 Manual
 |
View all Onkyo HT-R510 manuals
Add to My Manuals
Save this manual to your list of manuals |
Onkyo HT-R510 manual content summary:
- Onkyo HT-R510 | Owner Manual - Page 1
Antenna 22 Setup Powering Up & Setting Up the HT-R510 24 Configuring Speaker Set A 25 Operation Playing Your AV Components 28 Using the Tuner 30 Common Functions 32 Using the Listening Modes 34 Audio Adjust Functions 37 Recording 39 Remote Controller Using the Remote Controller RC-518M - Onkyo HT-R510 | Owner Manual - Page 2
When the power-supply cord or plug is damaged, B. If liquid has been spilled, or objects have fallen into the appliance, C. If the appliance has been exposed to rain or water, D. If the appliance does not operate normally by following the operating instructions. Adjust only those controls that are - Onkyo HT-R510 | Owner Manual - Page 3
/NFPA 70 GROUND CLAMP ELECTRIC SERVICE EQUIPMENT NEC - NATIONAL ELECTRICAL CODE S2898A ANTENNA LEAD IN WIRE ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) For Canadian Models NOTE - Onkyo HT-R510 | Owner Manual - Page 4
antenna Remote controller & two batteries (AA/R6) Speaker cable labels * In catalogs and on packaging, the letter added to the end of the product name indicates the color of the HT-R510. Specifications and operation are the same regardless of color. Features Amp • 6-channel amplifier • 100 watts - Onkyo HT-R510 | Owner Manual - Page 5
, as shown. Using the Remote Controller To use the remote controller, point it at the HT-R510's remote control sensor, as shown below. The HT-R510's STANDBY indicator flashes while a signal is being received from the remote controller. Remote control sensor HT-R510 2 Insert the two supplied - Onkyo HT-R510 | Owner Manual - Page 6
no effect unless the POWER switch is set to ON. B STANDBY indicator (24) This indicator lights up when the HT-R510 is in Standby mode, and it flashes while a signal is being received from the remote controller. C DIMMER button (33) This button is used to adjust the display brightness. D DIGITAL INPUT - Onkyo HT-R510 | Owner Manual - Page 7
(28, 32) Indicator A lights up when speaker set A is on. Indicator B lights up when speaker set B is on. 2 MUTING indicator (32) This indicator flashes when the HT-R510 is muted. 3 Source/listening mode indicators (28, 36) These indicators display information about the currently selected source and - Onkyo HT-R510 | Owner Manual - Page 8
to the connector on another Onkyo AV component, for example, a CD player, DVD player, or cassette recorder. The HT-R510's remote controller can then be used to control that component. To use , you must make an analog RCA/ phono connection between your HT-R510 and the other AV component, even if they - Onkyo HT-R510 | Owner Manual - Page 9
9 P This page describes only those buttons that can be used to control the HT-R510 when the remote controller is in RCVR mode (Receiver mode). The other modes, and information on using the remote controller to control your other AV components, are explained on page 41. To select RCVR mode, press - Onkyo HT-R510 | Owner Manual - Page 10
Components Before Making Any Connections • Read the manuals supplied with your AV components. • Don't connect the power cord until you've completed all audio and video connections. Optical Digital Inputs The HT-R510's optical digital connectors have a shutter-type cover that opens when an optical - Onkyo HT-R510 | Owner Manual - Page 11
Multi-channel Not output Using the AC OUTLET The switched AC outlet on the HT-R510's rear panel can be used to supply power to another AV component, as shown. COMPONENT VIDEO ANTENNA VIDEO 1 / 2 / 3 DVD IN IN OUT AM FM 75 Y PB PR DIGITAL INPUT OPTICAL COAXIAL 2 1 REMOTE CONTROL - Onkyo HT-R510 | Owner Manual - Page 12
1 REMOTE CONTROL VIDEO 2 IN VIDEO 1 OUT IN DVD MONITOR IN OUT VIDEO S VIDEO IN OUT IN L SUBWOOFER PRE OUT R CD TAPE IN OUT IN FRONT SURR CENTER L L R VIDEO 2 VIDEO 1 R DVD SUB WOOFER DVD IN DVD player VIDEO OUT ■ Using S-Video Use an S-Video cable to connect the HT-R510 - Onkyo HT-R510 | Owner Manual - Page 13
the other DIGITAL OUT OPTICAL DIGITAL OUT COAXIAL COAXIAL FRONT L FRONT R SURR L SURR R CENTER SUBWOOFER ■ Using Multi-channel Connections Use a multi-channel RCA/phono audio cable to connect the HT-R510's L/R FRONT, L/R SURR, CENTER, and SUB WOOFER DVD IN connectors to the 5.1 analog outputs - Onkyo HT-R510 | Owner Manual - Page 14
an optical digital audio cable to connect the HT-R510's OPTICAL 2 DIGITAL INPUT to the optical output on your D-VHS recorder, as shown. COMPONENT VIDEO ANTENNA VIDEO 1 / 2 / 3 IN OUT AM FM 75 Y PB PR DIGITAL INPUT OPTICAL COAXIAL 2 1 REMOTE CONTROL VIDEO 2 IN VIDEO 1 OUT IN DVD - Onkyo HT-R510 | Owner Manual - Page 15
the HT-R510's L/ R VIDEO 3 INPUT connectors to the analog audio outputs on your camcorder, games console, etc., as shown. STANDBY/ON POWER ON OFF A SPEAKERS B PHONES STANDBY DISPLAY SUBWOOFER DIMMER DIGITAL INPUT MODE CH SEL LEVEL CONTROL SUBWOOFER LEVEL DIRECT STEREO SURROUND DSP - Onkyo HT-R510 | Owner Manual - Page 16
cable to connect the HT-R510's OPTICAL 2 DIGITAL INPUT to the optical output on your satellite/cable tuner, LD player, etc., as shown. OPTICAL 2 COMPONENT VIDEO ANTENNA VIDEO 1 / 2 / 3 DVD IN IN OUT AM FM 75 Y PB PR DIGITAL INPUT OPTICAL COAXIAL 2 1 REMOTE CONTROL VIDEO 2 IN VIDEO - Onkyo HT-R510 | Owner Manual - Page 17
RCA/phono audio cable to connect the HT-R510's L/ R TAPE IN connectors to the audio outputs on your turntable, as shown. COMPONENT VIDEO ANTENNA VIDEO 1 / 2 / 3 DVD IN IN OUT AM FM 75 Y PB PR DIGITAL INPUT OPTICAL COAXIAL 2 1 REMOTE CONTROL VIDEO 2 IN VIDEO 1 OUT IN DVD MONITOR - Onkyo HT-R510 | Owner Manual - Page 18
another RCA/phono audio cable to connect the HT-R510's L/R TAPE OUT connectors to the cassette recorders inputs, as shown. COMPONENT VIDEO ANTENNA VIDEO 1 / 2 / 3 DVD IN IN OUT AM FM 75 Y PB PR DIGITAL INPUT OPTICAL COAXIAL 2 1 REMOTE CONTROL VIDEO 2 IN VIDEO 1 OUT IN DVD MONITOR - Onkyo HT-R510 | Owner Manual - Page 19
) you can control your compatible Onkyo CD player, DVD player, or cassette recorder with the HT-R510's remote controller, and use the following special functions: ■ Auto Power On When you turn on an AV component connected via while the HT-R510 is in Standby, the HT-R510 automatically turns on - Onkyo HT-R510 | Owner Manual - Page 20
your HT-R510: speaker set A and speaker set B. With speaker set A, which should be installed in your main listening room, and can be used with Dolby Digital or DTS surround material, you can connect front-left, front-right, center, surround-left, surround-right, surround-back, and subwoofer speakers - Onkyo HT-R510 | Owner Manual - Page 21
to which terminals. Subwoofer Front speakers Right Left Speakers Set A Surround speakers Surround back Right Left Center speaker speakers COMPONENT VIDEO ANTENNA VIDEO 1 / 2 / 3 DVD IN IN OUT AM FM 75 Y PB PR DIGITAL INPUT OPTICAL COAXIAL 2 1 REMOTE CONTROL VIDEO 2 IN VIDEO - Onkyo HT-R510 | Owner Manual - Page 22
COAXIAL 2 1 REMOTE CONTROL VIDEO 2 IN VIDEO 1 OUT IN DVD MONITOR IN OUT VIDEO S VIDEO IN OUT IN L SUBWOOFER PRE OUT R CD TAPE IN OUT IN FRONT SURR CENTER L L R VIDEO 2 VIDEO 1 R DVD SUB WOOFER FRONT SPEAKERS B FRONT SPEAKERS A L SURROUND SPEAKERS L CENTER SPEAKER AC - Onkyo HT-R510 | Owner Manual - Page 23
outdoor antenna should be situated well away from power lines and other high-voltage equipment. • Outdoor both FM and TV reception, as this can cause interference problems. If circumstances demand it, use a TV/FM antenna splitter manual. TV/FM antenna splitter To AV reciever To TV (or VCR) 23 - Onkyo HT-R510 | Owner Manual - Page 24
Powering Up & Setting Up the HT-R510 STANDBY/ON DIGITAL INPUT TAPE STANDBY/ON STANDBY/ON A SPEAKERS B PHONES STANDBY DISPLAY SUBWOOFER DIMMER DIGITAL INPUT MODE MEMORY FM MODE CLEAR AUDIO SELECTOR DVD VIDEO 1 VIDEO 2 VIDEO 3 VCR DIRECT STEREO SURROUND DSP PRESET/ADJUST TUNING - Onkyo HT-R510 | Owner Manual - Page 25
the number of speakers that you are using. Home Theater in a box (HT-S760) If you're using all of the supplied speakers for 6.1-channel surround, you don't need to set this function. 1 SPEAKER ADJUST Press the [SPEAKER ADJUST] button. The current speaker configuration is displayed. 2 PRESET/ADJUST - Onkyo HT-R510 | Owner Manual - Page 26
system, you need to set the crossover frequency according to the size and frequency response of your subwoofer and other speakers (front, center, and surround). If you're not using a subwoofer, bass sounds are output by the other speakers and this setting has no effect. Home Theater in a box (HT - Onkyo HT-R510 | Owner Manual - Page 27
the HT-R510 is muted (see page 32). 1 Press the remote controller's [TEST] button, and turn up the vol- ume so that you can hear the test tone sufficiently. While each speaker outputs the test tone (pink noise), its name appears on the display, as shown. 2 Use the remote controller's [CH - Onkyo HT-R510 | Owner Manual - Page 28
through the HT-R510. See pages 10-19 for information on connecting your AV components to the HT-R510. STANDBY/ON A SPEAKERS B PHONES STANDBY DISPLAY SUBWOOFER DIMMER DIGITAL INPUT MODE MEMORY FM MODE CLEAR AUDIO SELECTOR DVD VIDEO 1 VIDEO 2 VIDEO 3 VCR DIRECT STEREO SURROUND DSP - Onkyo HT-R510 | Owner Manual - Page 29
and Treble functions, press the [DIRECT] button. "Tone Off" appears on the display. Notes: • To use the multi-channel inputs, you must connect an AV component with individual 5.1-surround analog outputs to the HT-R510's multi-channel inputs. • You can select Multich only when the DVD input source is - Onkyo HT-R510 | Owner Manual - Page 30
VOLUME PRESET/ADJUST TUNING STANDBY/ON A SPEAKERS B PHONES STANDBY DISPLAY SUBWOOFER DIMMER DIGITAL INPUT MODE MEMORY FM MODE CLEAR AUDIO SELECTOR DVD VIDEO 1 VIDEO 2 VIDEO 3 VCR DIRECT STEREO SURROUND DSP PRESET/ADJUST TUNING SPEAKER ADJUST AUDIO ADJUST MASTER VOLUME TAPE - Onkyo HT-R510 | Owner Manual - Page 31
You can easily select previously stored presets as follows. 1 TUNER Remote controller Use the [TUNER] input selector button to select either AM ] button. The selected preset is deleted and its number disappears from the display, as shown. Other Functions: See page 32 for functions that you can - Onkyo HT-R510 | Owner Manual - Page 32
mode for speaker set A is set to Stereo. Muting the HT-R510 (remote controller only) With this function you can temporarily mute the output of the HT-R510. Remote controller Press the remote controller's [MUTING] button. The output is muted and the MUTING indicator flashes on the display, as - Onkyo HT-R510 | Owner Manual - Page 33
→ Surr Back → Surr Left → Subwoofer. You can adjust the volume of each speaker from -12 dB to +12 dB. The name of the currently selected speaker and its volume appear on the display, as shown. Using the Sleep Timer (remote controller only) With the sleep timer you can set the HT-R510 so that it - Onkyo HT-R510 | Owner Manual - Page 34
and DSP programs, the HT-R510 can transform your home listening room into a movie theater or concert hall. To get the most from surround sound, it's important that you install and configure your speakers correctly. See "Installing Your Speakers" on page 20 and "Configuring Speaker Set A" on page 25 - Onkyo HT-R510 | Owner Manual - Page 35
can experience the same superb sound that you get at a movie theater or concert hall. Use this mode with DVDs that bear the Dolby Digital logo. Dolby Digital EX: Dolby Digital EX decoding with up to 6.1 channels. With an added surround-back channel, this 6.1 channel format offers a heightened sense - Onkyo HT-R510 | Owner Manual - Page 36
differently to the HT-R510's [DSP] button. • HT-R510 [DSP] button: You can select the following Onkyo DSP modes: Orchestra, Unplugged, Studio Mix, TV Logic, and All Ch St. • Remote controller's [DSP] button: You can select all of the currently available listening modes (basic, surround, and DSP - Onkyo HT-R510 | Owner Manual - Page 37
's [AUDIO/ADJUST] button, press its [RCVR/TAPE] button to select RCVR mode. 2 PRESET/ADJUST Remote controller Use the [PRESET/ADJUST] buttons on the HT-R510, or the ADJUST buttons on the remote controller to set the selected function. Note: The Cinema Filter and Late Night functions can be - Onkyo HT-R510 | Owner Manual - Page 38
HT-R510 to Standby. ■ Cinema Filter With this function, you can soften the harshness, or brightness sometimes experienced with movie soundtracks, which are typically mixed for reproduction in a movie theater. ■ Center Image (DTS Neo:6 Music) The DTS Neo:6 surround format derives its center-channel - Onkyo HT-R510 | Owner Manual - Page 39
on connecting your AV components to the HT-R510. STANDBY/ON A SPEAKERS B PHONES STANDBY DISPLAY SUBWOOFER DIMMER DIGITAL INPUT MODE MEMORY FM MODE CLEAR AUDIO SELECTOR DVD VIDEO 1 VIDEO 2 VIDEO 3 DIRECT STEREO SURROUND DSP PRESET/ADJUST TUNING SPEAKER ADJUST AUDIO ADJUST - Onkyo HT-R510 | Owner Manual - Page 40
's AV components, some of the remote controller's buttons may not work as expected. By default, the [CD/DVD] button is set to code 316, which is for use with an -compatible Onkyo DVD player connected to the HT-R510's connector. To control an -compatible Onkyo CD player connected to the HT-R510 - Onkyo HT-R510 | Owner Manual - Page 41
at anything for this step.) 3 Use the remote controller's Power [ ] button to turn on the AV component. Remember, if your AV component is connected to the HT-R510 via , point the remote controller at the HT-R510. If not, point the remote controller at the AV component. (A cassette recorder can't be - Onkyo HT-R510 | Owner Manual - Page 42
TV MUTE 4. VCR control buttons Control TV if appropriate TV code has been entered 1. Input Selectors 3. TV control buttons Control VCR if appropriate VCR code has been entered Power on/off Enter numbers Select next received channel Select previous received channel Start playback Stop playback - Onkyo HT-R510 | Owner Manual - Page 43
control buttons 1. Input Selectors 1. Input Selectors 1-9, 0 CH+ CH- MENU // / ENT Power on/off Enter numbers Select next channel Select previous channel Confirm Select next channel preset Select previous channel preset Display menu Select menu items * Since you can only enter a Cable code - Onkyo HT-R510 | Owner Manual - Page 44
it, then try turning it on again. The HT-R510 shuts down immediately after being turned on? The amp protection system has been activated. Contact your Onkyo dealer. The buttons on the HT-R510 and remote controller don't work? Power supply voltage fluctuations and other anomalies, such as - Onkyo HT-R510 | Owner Manual - Page 45
as far HT-R510 are too close to the power cord. away as possible from the power cord. The sound is too bright or harsh and the high range is The Treble function is set too high. not clear. Adjust the Treble function (pages 29, 37). The subwoofer mode is set to OFF or is set incorrectly. Check - Onkyo HT-R510 | Owner Manual - Page 46
Digital or DTS source material. Although you cannot record Dolby Digital or DTS surround channels, you can record the left and right channels by connecting the source AV component's analog left and right outputs to a pair of analog inputs on the HT-R510. The wrong input source is selected on your - Onkyo HT-R510 | Owner Manual - Page 47
Power output (FTC) All channels: 100 watts per channel min. RMS at 8 Ω, 2 channels driven from 20 Hz to 20 kHz with no more than 0.08% Dynamic power output: total harmonic distortion. 230 watts × 2 at 3 Ω 170 watts × 2 at 4 Ω 115 watts REMOTE CONTROL Transmitter: Signal range: Power supply - Onkyo HT-R510 | Owner Manual - Page 48
SN 29343479 Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8111 Fax: 072-831-8124 ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.onkyousa.com ONKYO EUROPE ELECTRONICS
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
 |
 |
AV Receiver
HT-R510
Instruction Manual
Thank you for purchasing the Onkyo AV Receiver.
Please read this manual thoroughly before making con-
nections and plugging in the unit.
Following the instructions in this manual will enable you
to obtain optimum performance and listening enjoyment
from your new AV Receiver.
Please retain this manual for future reference.
Contents
Introduction
Important Safeguards
................................................
2
Precautions
................................................................
3
Supplied Accessories
................................................
4
Features
.....................................................................
4
Before Using the HT-R510
.......................................
5
Controls & Connectors
.............................................
6
Connections
Connecting Your AV Components
.........................
10
Connecting -compatible AV Components
..............
19
Installing Your Speakers
........................................
20
Connecting Antenna
...............................................
22
Setup
Powering Up & Setting Up the HT-R510
..............
24
Configuring Speaker Set A
.....................................
25
Operation
Playing Your AV Components
...............................
28
Using the Tuner
......................................................
30
Common Functions
.................................................
32
Using the Listening Modes
.....................................
34
Audio Adjust Functions
..........................................
37
Recording
................................................................
39
Remote Controller
Using the Remote Controller RC-518M with Your
Other AV Components
........................................
40
Appendix
Troubleshooting
......................................................
44
Specifications
..........................................................
47
E
n